The keys to ensuring that your wooden gate won't sag are to build and reinforce the gate frame so it doesn't warp, to hang the gate plumb and to distribute the weight of the gate over as much area as possible. Building a strong wooden gate requires no special tools or advanced carpentry skills. The old-fashioned technique of using diagonal wooden braces in each corner of the frame takes a little longer than installing a single diagonal brace across the middle of the frame, but produces a durable gate that will resist warping for many years.
Things You'll Need
- Pencil and paper
- Measuring tape
- Chop saw
- 2-by-4-inch pressure-treated planks
- 1-by-4-inch pressure-treated planks
- L-shaped steel corner brackets
- Carpenter's square
- Drill and driving bit
- 1 1/2-inch coated or galvanized screws
- Infill planks
Draw your gate plan on paper. Include height and width dimensions of the gate. The gate will include a rectangular frame with mitered corners, wooden diagonal corner braces and infill material. Your chosen infill may be wooden planks, pickets, wire mesh, bamboo or nearly any durable material that you can attach to the frame. Refer to your sketch as you construct the gate.
Set the chop saw to make 45-degree cuts. Trim one end of a 2-by-4-inch plank by placing the plank on the table of the saw with the 4-inch surfaces of the plank horizontal. Hold the plank firmly against the guide fence when cutting. Measure and mark the plank on its longest edge to the length of your gate rails (horizontal framing members). Cut the rail to length. Make sure that the cut ends of the plank are divergent, not parallel. Measure, mark and cut a second rail to the same length as the first.
Refer to the dimensions on your sketch to measure, mark and cut the stiles (vertical framing members) from 2-by-4-inch planks. Trim one end of a 1-by-4-inch plank with a 45-degree cut. Divide the length of the shortest framing member by two to calculate the length of the wooden diagonal corner braces. Measure and mark this dimension on the longest side of the 1-by-4-inch trimmed plank. The plank will be oriented with its 4-inch surfaces horizontal on the saw table. Cut the first corner brace with the cut ends divergent, like the framing members. Measure, mark and cut three more corner braces to the same length as the first.
Arrange the rails and stiles on a flat surface so they form a rectangle with mitered corners, like a picture frame. Place an L-shaped steel corner bracket on the outside of the first corner of the frame. Center the bracket to the edge of the frame. Use a drill with a driving bit and 1 1/2-inch wood screws to attach the bracket to the mitered corner. Repeat to join each corner of the frame.
Place the wooden diagonal braces across the corners of the gate frame, aligning the cut-ends of the braces with the outside edges of the rails and stiles. Attach each brace to one framing member, with two evenly-spaced screws, 2 inches apart. Leave the opposite ends of the braces unattached. Lay a carpenter's square on one corner of the frame. Make adjustments to the positions of the framing members, if necessary, to square the corner. Screw the unattached end of the wooden brace to the corresponding framing member. Repeat to square and brace the remaining corners of the gate frame.
Turn the frame over so it rests on the wooden braces. Test fit the infill material by arranging it on the frame. Mark and trim the infill material if necessary. Use screws to attach wooden or bamboo infill material. The first and last pickets, planks or canes should be attached to both the rails and stiles of the frame. Interior infill material should be attached to opposite framing members with two evenly-spaced screws on each end. Your finished gate may be installed on the gatepost, using appropriate mounting hardware.
- Photo Credit Jupiterimages/Photos.com/Getty Images
How to Build a No Sag Privacy Fence Gate
Building a no-sag wooden privacy fence gate is a simple ... The keys to ensuring that your wooden gate won't sag are...
How to Install a Cable & Turnbuckle on a Wooden Gate
Over time, your wooden gate may begin to sag. The latch no longer operates properly and the gate begins to drag on...
How to Brace a Fence Gate
Bracing the gate itself is a simple process that can be accomplished with basic tools and supplies available ... one with corner...
How to Repair Sagging Fence Gates
Your fence looks great, but your gates are sagging. Nothing is more frustrating than dragging a lawnmower , or an uncooperative pet...
How to Repair a Sagging Gate
Before you try to fix a sagging wooden gate, you must first diagnose the problem. Worn-out hardware or stripped screw holes may...
How to Build a Walk Through Gate
How to Build a No Sag Privacy Fence Gate. Wooden privacy fence gates are typically at least 6-feet tall and wide enough...
How to Build a 6 X 6 Gate
Sketch your plans for the finished gate; include dimensions for the rails, stiles, and infill material. ... To prevent an especially heavy...
How to Build a Gate for a Deck
How to Build a Gate for a Deck. A deck with a handrail should have a fence. If the deck is higher...