How to Glue a Rubber Membrane on a Wood Deck

Save

Using a rubber membrane on a wood deck is a good way to create a waterproof surface that can be further improved upon. This is generally useful when you intend to have something under the decking in need of protection, such as another room when building a roof deck. Rubber membranes are primarily used as an undercoating, protection that is laid down before a final layer of tiles or planks. It can also be used on an existing deck prior to the application of a new deck surface such as tiles. Gluing the rubber membrane to the deck can be done by just about anyone if you carefully follow the installation procedure.

Things You'll Need

  • Stiff bristle push broom
  • Detergent
  • Water
  • WPDM rubber membrane
  • Utility knife
  • Latex bonding adhesive
  • Termination bar
  • Screws
  • Prepare the wood deck by thoroughly cleaning it. Sweep the surface of the deck, removing any loose dirt or debris, then wash it using a mild detergent to clean any ingrained dirt. Rinse with clean water in order to remove any residue from the cleanser.

  • Inspect the deck for any damage. If there are split or rotted boards present, replace them immediately, sealing the new wood boards and allowing the sealant to completely dry.

  • Roll the rubber membrane onto the deck. Place the sheets of rubber with the seams overlapping by 4 inches and the outer edges overhanging the edges of the deck by 3 inches. Use a utility knife to make cutouts of the material where necessary for fitting around objects protruding from the deck.

  • Pull back a sheet of membrane from the deck surface, folding it over onto the other half and exposing the deck. Apply a thick layer of adhesive onto the deck using a 1/2 inch nap roller on an extension pole. Allow the glue to set for three minutes and then place the membrane back onto the deck. Use a push broom driven along the surface of the rubber to push out any bubbles or wrinkles in the membrane.

  • Raise the second half of the membrane sheet and repeat the gluing process, making sure the entire surface of the deck beneath the full sheet has been layered with the adhesive.

  • Repeat the process for the remaining sheets of rubber membrane.

  • Seal the overlapping seams with soft paper-backed adhesive tape. Mark a line using chalk one inch past the seam edge onto the overlapped membrane, then pull back the overlapping membrane. Apply a layer of seam primer to the overlapping surfaces of both rubber membranes and allow the primer to dry.

  • Place the seam tape onto the bottom sheet of the overlap, with the edge of the tape following your chalked line. Set the tape by rolling over it with a seam roller. Fold the top membrane over the tape. Remove the paper backing on the tape, pressing onto the overlapping membrane to form the seam. Set the seam by rolling over it with the seam roller.

  • Place a line of caulking between the membrane and any adjoining walls, then place a termination bar along the edge of the sheet. The termination bar is a metal strip which edges the rubber membrane. Screw the termination bar to the wall, then cut any excess membrane above the bar with the utility knife. Place another line of caulking between the termination bar and the wall at the top of the bar.

  • Overlap the edges of the membrane over the edges of the deck and glue them into place using the adhesive on the deck edge. Place a termination bar over the edges, applying the caulk as with the wall placements. Trim off the excess membrane.

References

  • Photo Credit Jupiterimages/Photos.com/Getty Images
Promoted By Zergnet

Comments

Resources

You May Also Like

  • How to Attach a Roof Deck Over Membrane

    EPDM, a type of rubber membrane, offers an affordable way to cover flat roofs. And if your flat roof looks like the...

  • How to Use an EPDM Roof for a Deck

    You may have an older urban home with an existing upper story door leading out to a newish, flat EPDM rubber roof....

  • How to Glue Rubber

    The fact that rubber stretches makes it somewhat difficult to glue. The problem that most people find when gluing rubber is that...

  • How to Install a Roof Rubber Membrane

    Flat roofing methods are susceptible to leaks caused by inflexibility, weathering, and failing joints. Ethylene propylene diene Monomer (EPDM) rubber roofing is...

  • How to Install Tile Over Decking

    Tile can be installed in many places inside and outside the home, including a deck, as an alternative to sanding and staining...

  • How to Bond Butyl Rubber

    Butyl rubber is one of the most durable sealing compounds on the market. This particular type of caulk is intended for applications...

  • How to Install Tile on EPDM

    EPDM is a roofing membrane used to provide a waterproof layer on flat rooftops. Most of these layered rooftops remain empty, but...

  • How to Glue Rubber to Wood

    If you have a project that requires you to glue rubber to wood, such as in stamp-making, it can seem a little...

  • How to Install Rubber Deck Tiles

    No matter the outside surface, whether it's the concrete slab of most patios, brick or clay pavers, or even the wood of...

  • How to Install Pavers Over an EPDM Membrane

    Masonry pavers are a popular material for patios and decks. Putting them over a material called ethylene propylene diene monomer (EPDM) will...

  • How to Glue EPDM to Wood

    Ethylene propylene diene terpolymer, or EPDM, roofing membranes are durable and quick to apply, making them the first choice of many contractors...

  • How to Coat a Rubber Membrane Roof

    Over time the rubber membrane on a roof deteriorates, causing leaks that need repair. Extreme weather conditions can tear rubber. The resultant...

Related Searches

Check It Out

22 DIY Ways to Update Your Home on a Small Budget

M
Is DIY in your DNA? Become part of our maker community.
Submit Your Work!