How to Replace Felt On Flat Roof

Save

Replacing the felt on your flat roof is not a job for everyone, but anyone can do the job by following a few simple directions. The most important concept in replacing your roof felt is making sure the base is in great condition. If your decking material isn't of the highest quality, no amount of felt is going to make your roof waterproof and strong. Follow the instructions carefully and you will soon have a roof you'll be proud to show off.

Things You'll Need

  • Hammer
  • Tape Measure
  • Strong Cutting Knife
  • Nails
  • Felt
  • Adhesive
  • Chipping Material
  • Broom

Replace Felt On Flat Roof

  • Prepare the foundation. Before laying 30 lb felt on a flat roof make sure the plywood base is in good condition. Any rotten decking should be replaced before laying the felt. All new boards should be coated first with a preservative. Once your roof decking is suitable, you are ready to begin replacing the felt.

  • Remove excess felt, nails, and adhesive before replacing the felt on your flat roof. Allow any wet plywood to dry out. There should be no extra debri of any kind on the decking before you begin.

  • Nail the first layer of felt to the plywood using 20mm galvanised clout nails with large heads spaced every 150mm along the planks. Make sure the felt is straight and flat. Always start nailing in the center of the felt sheet working your way outward towards the edge of the roof. Do not nail on the edge of the roof where the second layer of felt will overlap the first.

  • Paint a layer of adhesive, such as bitumen mastic, over the top of the first felt layer, a length at a time. The second layer of felt is then placed over the top of the first. Do not let the ends join together. There must be an overlap to prevent leaking. Either use a broom, or if the roof is strong enough, walk over the top of the roof felt to get rid of any air bubbles.

  • Cover the roof edges with strips of felt before laying the final layer of roof felt. Remember to allow 50mm of overlap with each piece of felt layed. Paint bitumen mastic over the top of the entire final layer of felt to provide the most waterproofing. To strengthen the surface of your new felt roof cover the surface with gravel, granite, or limestone.

Tips & Warnings

  • When laying down your layers of felt roll out about 1 metre so that you are only working on a small area at a time.
  • After laying down a top layer of roof felt make sure that the overlap is secure by painting more adhesive over the top.
  • Adding loose chipping material to your final felt roof prevents the surface from absorbing the sun.
  • Make sure your shoes are free from sharp edges that would cut or damage the just laid felt.
  • Only use nails on your first layer of roof felt. The subsequent layers of felt are secured by adhesive only.

Related Searches

Promoted By Zergnet

Comments

You May Also Like

  • How to Repair a Flat Roof

    Water runs right off of sloped roofs, but flat ones must maintain a watertight seal to prevent leaking. When you have a...

  • How to Pitch a Flat Roof

    So you want to pitch your flat roof. It might be that you want to add attic space or simply change the...

  • How to Felt Paper a Roof Valley

    Slope type roofs are among the most frequently built and are usually the most cost-effective option. Any structure that has a floor...

  • How to Repair Roofing Felt

    Roofing felt has become a necessity in composite roofing systems, acting as an effective second line of defense against moisture and weather....

  • How to Install Roofing on a Flat Roof

    Installing roofing on a flat roof is a job a homeowner can accomplish on their own. With the proper tools and an...

  • How to Refelt a Flat Roof

    When installing any type of roof, laying down the felt underlayment is always one of the first steps. This underlayment is used...

Related Searches

Check It Out

22 DIY Ways to Update Your Home on a Small Budget

M
Is DIY in your DNA? Become part of our maker community.
Submit Your Work!