Valspar Metallic Paint Glaze Directions

Save

Valspar's line of Faux Finish paints and glazes give you an excellent opportunity to add a special touch to your paint job. Proper surface preparation and application, however, takes some serious and careful work. If you're willing to put in some extra time to give your paint job an extra special touch, Valspar's Metallic and Patina Glazes are a great way to do so.

Things You'll Need

  • 1 gallon of Valspar Metallic Paint Glaze per 125 to 200 sq. ft. of painting surface (depending on surface porosity)
  • 1 gallon of Valspar base coat per 350 to 400 sq. ft. of painting surface (depending on surface porosity)
  • Professional-grade paintbrush
  • Professional-grade roller
  • Wallpaper smoothing brush
  • Prepare your painting surface properly. Ensure that the surface is clean and free of debris and peeling paint. Tape off all moulding, baseboards and trim, and lay drop cloths over the floor to avoid splatters. If you're working with new wallboard, use a primer.

  • Apply a base coat. Many of Valspar's Faux Finishes call for a specific base coat, which can be mixed by your paint vendor. Otherwise, apply whichever base coat color suits your decor. Remove your tape and allow your base coat to dry for at least four hours or overnight before moving on to glazes.

  • Reapply your tape and apply your Metal Glaze in sections 4 to 6 feet wide, using rollers and brushes.

  • Work through your wet glaze with a wallpaper smoothing brush. Use a sweeping motion of large, overlapping arcs to allow the base color to show through the glaze in some spots. This will give the finish the look of brushed metal. Glaze remains workable for 30 minutes.

  • Repeat Steps 3 and 4, in 4-to-6 foot sections, until your entire painting surface is covered. Remove your tape and allow the glaze to dry overnight.

Tips & Warnings

  • Avoid drafts from open windows and fans.
  • Higher-end brushes, rollers and other tools make a difference. Remember that the result of your project should last for years and spend a little extra for good materials
  • Adding a second coat will give your glaze a richer metallic sheen.
  • For added protection, apply 1 gallon of Valspar® SignatureColors® FauxClear Protector per 400 sq. ft. of painting surface (depending on surface porosity) after all coats of glaze are dry.
  • When working with new wall coatings, always test first on a small, less-conspicuous area before proceeding.
  • Practice your paint and glaze technique on a practice board before applying it to the wall.
  • Read the entire label before using, especially all instructions and warnings.

References

  • Photo Credit Jupiterimages/Photos.com/Getty Images
Promoted By Zergnet

Comments

Resources

You May Also Like

  • Valspar Glaze Techniques

    Valspar glaze is a transparent faux-finish coating that comes in a variety of types and colors. ... metal and patina glazes create...

  • How to Use Valspar Translucent Glaze

    Valspar Metallic Paint Glaze Directions. Valspar's line of Faux Finish paints and glazes give you an excellent opportunity to add a special...

  • Valspar Faux Techniques

    How do I Convert Behr Paint Color to Valspar? Valspar paints were created with the do-it-yourselfer in mind. ... Valspar Metallic Paint...

  • Metallic Interior Paint Colors

    Interior metallic paints are made by combining metallic pigment powders with latex interior paint. You can purchase the pigment powders separately and...

  • Brushed Metal Glaze Wall Painting Technique

    ... from traditional bronze and copper to modern jewel tones such as blue turquoise and ruby red. ... Valspar Metallic Paint Glaze...

Related Searches

Read Article

5 Small Entryway Decorating Ideas

M
Is DIY in your DNA? Become part of our maker community.
Submit Your Work!