Changing an old, worn, out-of-style front door with a modern one can increase curb appeal and replacing a drafty, ill-fitting with a properly fitting door and frame can lower heating and cooling costs. Pre-hung exterior doors and frames are sold ready for installation.
Things You'll Need
- Pry bar
- Large putty knife
- Tape measure
- Reciprocating saw
- Dust pan
- Felt paper
- Roofing nails
- Bubble level
- 16 p nails
- 3-inch screw
- Non-expanding foam sealant
- Finishing nails
- Foam caulking backer
Remove the trim on both the inside and outside of the old door. Place a putty knife against the drywall under the edge of the trim. Slide the pry bar under the trim but above the putty knife. Pull the trim off. Remove any nails with a hammer. This exposes the rough door opening, which is the space in the framing that the door package fits into.
Measure the height and width of the door, exterior casing, jam width, trim width and the rough opening with a tape measure. Round the size of the door up to the next full inch.
Buy a door package that fits your measurements. Pay attention to the rough-opening measurements. The new door frame must be slightly smaller than the rough opening for it to fit.
Remove the old door's hinge pins with a hammer and punch. Set the old door aside.
Remove the old door frame. Cut through the nails that hold it in place with a reciprocating saw. Slide the door frame out after the nails have been cut.
Clean up debris with a broom and dust pan. Clean out the gaps around the rough opening.
Inspect the rough opening and sill for damage. Replace all damaged areas.
Wrap the rough opening with strips of felt paper. Secure it with roofing nails.
Apply caulking to the sill and the new door casing. The caulking beads must be unbroken and extend completely across the sill and all the way around the casing. Fill the bottom corners.
Set the door frame in place. Push the casing tight to the wall.
Center the door frame in the rough opening. Use a bubble level to check the frame for plumb. Push shims between the frame and the rough opening at the top, bottom and middle. Tack the frame corners in place with 16 p nails
Double-check the door frame for plumb and level. Place a bubble level on each side of the jam and the top plate. Adjust the shims as needed.
Hammer 16 p nails every 16 inches along the hinge side of the exterior casing. Open and close the door to verify that the door works properly.
Finish securing the door frame casing. Drive 16 p nails every 16 inches along the top and latch side. Screw the threshold to the sill. Remove one screw from each hinge. Install a 3-inch screw in its place with a drill.
Fill the area between the door frame casing and the rough opening with a non-expanding foam sealant. Allow the foam to dry. Remove any excess with a putty knife.
Install the trim with finishing nails. Caulk the edges and seams. Large gaps require a foam-caulking backer.
Tips & Warnings
- One person can complete this project but it is much easier with a helper.
- Photo Credit front door image by Derek Abbott from Fotolia.com
How to Replace an Exterior Door
A new exterior door is a quick and easy way to upgrade the curb appeal of your home. It's also a good...
How to Replace a Rotting Exterior Door Frame
In order to repair a rotted or partially rotted door frame, you must remove and then replace the portion where rot has...
How to Frame an Exterior Door
Framing an exterior door properly is important because it allows the door to operate smoothly and close with a secure, weatherproof seal....
How to Replace a Wooden Door Frame
If your door frame has become warped, skewed, damaged, or otherwise ineffective, you should replace it. Similarly, you may need to replace...
How to Replace a Front Door Glass Insert
Front door glass does more than let in light, it lets you see who is there before you open the door. While...
DIY: How to Replace a Door Frame
Do it yourself projects do not have to be challenging and with the proper knowledge and tools even the most labor intensive...