DIY Party Barge Plans

Save

Barges are flat-bottomed, shallow-draft watercraft that were originally used to carry freight and cargo on calm rivers and lakes. They are usually not powered and require tugs or push-boats. Heavy work barges are used as a stable platform for dredging and construction projects. In recent years, barges have found their way into recreation. Party barges with wraparound seating and fun-time amenities just beg for an occasion to get the gang on board for a day of festivities. Here is a design that incorporates surprising performance along with comfort and versatility.

Basic Party Barges

  • Most entry-level to mid-grade party barges integrate an aluminum frame and a carpeted marine plywood deck over two aluminum pontoons to supply buoyancy and a somewhat streamlined hull profile to the water. The pontoons are displacement hulls, however, and require far more power to move through the water than the planing hulls of normal runabouts that run on top of the water. All displacement hulls have a terminal velocity defined by the hull’s length because the craft cannot go any faster without creating a vacuum behind it. From that point, adding power merely generates more turbulence and wake with no increase in speed. Therefore, most party barges traverse the water at moderate speed at wide-open throttle and leave huge wakes.

Technology Break

  • Nuclear submarines running at high speed underwater face the same issue. They overcome it by streaming air bubbles out at the nose of the sub, which effectively lowers the resistance of the hull moving through the water. This same influence can be put to work on the party barge to noticeably improve the performance. Most party barges have a single outboard engine pod on the extreme aft between the two pontoons. This novel design puts one smaller outboard engine in front of each of the two pontoons. While the main thrust of each propeller is directed under and not at the pontoon behind it, the entrained air in this turbulence quickly rises to the surface and moves along the surface of pontoons until it reaches the rear-most section and breaks the suction behind it. The other positive effect is that the outboards also tend to flatten the surface before the boat gets to it, which smoothes the ride.

Modifications

  • Barges designed for a single 50-horsepower outboard motor should get two front-mounted 30-horsepower units. A 90-horsepower design should get two 50-horsepower units. Beam cages will need to be constructed from the front of the pontoons to provide twin transoms in front of the barge. These transoms should then have half-eggshell baffles on the front to protect the motor connections. These should be made from fiberglass over hard foam. Wiring, steering and other controls, including fuel, should be moved forward. Batteries, fuel tanks and all other mechanisms should be moved aft to a platform extending between the two pontoons to help offset the forward weight. The captain’s helm should be moved rearward into a raised, center console-type helm at the extreme rear of the barge. This will help offset some of the forward weight.

Commanding View

  • The rear-mounted raised helm provides an exhilarating view of the entire ship as it moves forward smoothly and powerfully with its new power and operating strategy.

References

Promoted By Zergnet

Comments

Resources

You May Also Like

  • How to Become a Barge Captain

    A barge is a vessel used in the workboat industry. These large, flat-bottomed boats are used to transport freight. As the captain...

  • How to Build a Dock on a River

    The river winds lazily past your house, and provides a relaxing backdrop as you wind down for the evening. This would be...

  • DIY: Boarding Pass Invitations

    Planning a party requires invitations to let the guest know the party details. You can always purchase generic invitations at your local...

  • How do I Put Foam in Plastic Barrels to Float Them?

    Filling a plastic barrel with expanding urethane foam will produce a highly buoyant float which may be left in contact with water...

  • How to Make a Pontoon With 55 Gallon Drums

    Pontoon boats are expensive. It is fun to go out and fish, have a party, of just hang out and relax on...

  • Homemade Plywood Pontoons

    Pontoons are generally used to make a pontoon boat or raft because they easily float on water. Building your own pontoon boats...

  • Homemade Plastic Barrel Pontoons

    Pontoon boats, generally constructed with plastic barrels and plywood, are the ideal platform for slow moving rivers where the water is calm...

  • How to Build a House Barge

    Building your own small house barge is a good weekend pastime that will encourage you to take advantage of the outdoor and...

  • How to Build a Barge With Aluminum Foil

    A model of a barge made from aluminum foil is a project assigned by many science teachers, Scout Masters and 4-H leaders....

  • Types of Barges

    Barges are used to transport cargo and for general utility purposes. Typically a flat-bed vessel, a barge is towed or pushed by...

  • DIY Pontoon Boats

    Imagine a peaceful float on the water, enjoying the sunshine or casting a line: Pontoon boats are the ideal platform for such...

Related Searches

Check It Out

How To Travel For Free With Reward Points

M
Is DIY in your DNA? Become part of our maker community.
Submit Your Work!