Homemade Jib Crane

Save

Jib cranes range in size from hundreds of pounds to tens of tons. They are known for long boom arms and swiveling or rotational capability. They are widely used in industry to load freight and move equipment. Their greatest visibility may well be on the docks where freighters are loaded and unloaded. This is a homemade portable unit that allows engine removal from vehicles, lifts and moves heavy furniture and equipment, and enables loading heavy items onto pickup trucks.

Jib Crane Strategy

  • The unit has a 6-foot high vertical boom with a 4-foot horizontal boom. The vertical boom is welded to a 4-foot wide boom that forms the base of a "U" with two 4-foot horizontal legs. This U-shaped frame is parallel to the ground and has four heavy-duty swivel wheels to allow easy rolling mobility. A 2-foot handlebar with grips is connected to the vertical boom at chest level so the operator can push and pull the unit up to the load. Lifting is performed by an 800-pound capacity handle winch with an automatic brake. Steel pulleys with 5/8-inch bores, bushed with oilite bearings, riding on ½-inch steel bolts at the end of the lifting boom supports the steel cable from the winch, which is mounted on the vertical boom arm.

Materials

  • All of the steel tubing used in the unit is 3-inch by 3-inch 3/16-inch thick square steel tubing. The vertical and horizontal booms are 5 and 4 feet long respectively. The legs are 4 feet long. They are welded to two 4-foot-wide sections of the tubing welded together to bolster the most critical section of the crane, since this double-beam transmits considerable torque to the legs from the vertical boom arm. All critical joints are further reinforced with welded rectangular 3/16-inch thick steel gusset plates 3 inches wide. Six of these should be 9 inches long and two should be 6 inches long. Four of the 9-inch-long pieces should be drilled in the corner quadrants, 1 inch in on a 45-degree line from the corners for the pulley bolts. Choose heavy swivel casters with threaded stem tops and weight capacities of at least 600 pounds each. Match the caster tops with 1/4-inch thick weld plates 5 inches longer than the caster top disk that have a bolthole to match the caster stem at one end (not centered).

Construction

  • Use 1/8-inch type 6013 rods to weld all joints. Grind the welds where gusset plates go flat. This is fine since 6013 rods produce welds with penetration into the space between pieces. When the gusset plates are welded on, the joint will be staggered with contiguous material on two levels and extremely strong. Weld the caster plates on tops of the ends of the legs. Chip and brush all welds with a stiff rotary wire wheel in a high-speed drill. Inspect the welds for well-defined continuous beads. Clean and paint the entire frame. Bolt the casters to the plates. Bolt the pulleys into the top boom gussets where they protrude from the top. Finally, use U-bolts to attach the winch to the vertical boom at about waist height. Put a keying bolt through the winch into the frame. Extend the winch cable over the two pulleys and hang the hook. The winch is now ready for use.

References

Promoted By Zergnet

Comments

Resources

You May Also Like

  • Boom Trucks Vs. Cranes

    Bucket trucks, boom trucks and cherry pickers all refer to the class a type of utility vehicle used for vertical work. These...

  • Homemade Gantry Crane

    A Gantry crane is a crane which has two or more legs standing vertically on each side, supporting a bridge going across...

  • DIY: Camper Shell Cap Pulley Hoist

    A camper shell is a useful addition to any pickup truck. It protects the cargo from the elements and allows you to...

  • DIY Gantry Crane

    A gantry crane is a structure that has at least two legs that support a bridge or beam. The device allows you...

  • How to Use Crane Trucks

    Cranes trucks have a myriad of uses from moving heavy objects to loading supply ships and hoisting equipment. That is why safe...

  • How to Make a Homemade Roller Furling

    Sailing is a simple act. Sails catch the prevailing wind off the water and move the boat. A skilled pilot can steer...

  • Instructions for Mounting a Pick Up Truck Lift Crane

    Adding a truck lift crane to the back of a pickup truck will make unloading and loading cargo easier. Available as powered...

  • How to Make a Jib Crane

    A jib crane can be created using either aircraft aluminum or wood, a tripod and high-quality barrings. Make a jib arm for...

  • Homemade Engine Hoist

    An engine hoist is a necessary piece of equipment for removing engines from all automobiles. Whether the vehicle is the family sedan,...

Related Searches

Check It Out

How To Travel For Free With Reward Points

M
Is DIY in your DNA? Become part of our maker community.
Submit Your Work!