What Are Bulkheads & Stringers on Boats?


An mnemonic for remembering shipboard terminology goes: "You lean on the bulkhead and stroll on the stringers." Bulkheads and stringers are boat parts that have on-shore equivalents. In spite of their odd names, they serve the same function as their counterparts ashore, as well as add to a boat's structural stability. Knowing that subtle differences marks you as a seafarer when you casually and correctly sprinkle these words in a conversation.

You Lean On the Bulkhead

  • A bulkhead is a wall. The American Merchant Seaman's Manual says that the bulkhead "provides privacy and encloses spaces within a ship." What the manual leaves unsaid is that the bulkhead is attached to lateral hull stiffeners in the same way that wall studs support a wall in a home. Although most bulkheads are thin, some -- like the collision bulkhead at the front of the ship -- are heavily made to withstand the pressure of the water in the event of a front-end collision.

You Stroll on the Stringer

  • The stringers are much like floor joists: they support the main deck and decks below the main deck. The stringers also provide room for concealed wiring that might run the length of the vessel. Stringers are concealed by the flooring on the decks below your feet and by the compartment "overheads," the ceilings of the cabins and compartments formed by bulkheads. The stringers provide a convenient attachment point for the overhead of a compartment.

The Bulkhead as a Structural Member

  • The bulkhead is loosely arranged as a shore-side home's wall, complete with a stud. Unlike a load-bearing wall of a home, the bulkhead doesn't provide structural strength. Instead, the frames that support the bulkhead, called bulkhead stiffeners, add the structure that surrounds a bulkhead. Some bulkheads, though, stand in the way of an invading ocean: should your boat become involved in a collision that breaches the forward end of the hull, the collision bulkhead stops water from entering the boat through the breach.

The Stringer as a Structural Member

  • Stringers run from the front to the rear of the boat's hull on all sides. One stringer is called the "keel." It runs from the bow of the boat -- the boat's front -- to the rear of the boat in the center of the bottom and acts as the backbone of the ship. Stringers placed between the frames around which a boat's hull is built provide longitudinal stiffness; they also keep the hull from bending in the middle like a rubber raft when the boat rides over a wave.


  • "Section 15-01 The American Merchant Seaman's Manual"; W.B. Hayler; 1981
Promoted By Zergnet


You May Also Like

  • What Are Boat Stringers?

    The water worthiness of a boat depends largely on the condition of its various parts. Stringers provide a form of structural support...

  • How to Replace a Floor in a Boat

    Over time, boat floors begin to show wear and tear from repeated exposure to the elements, specifically water. The need for a...

  • Names of Parts of a Boat

    The parts of a boat have funny names to a landsman. Many of the names go back hundreds of years and their...

  • What Are Bulkhead Seats?

    Bulkheads seats are those seats located right behind the bulkhead separators. Bulkhead separators are the physical partitions that separate different sections or...

  • How to Check for Bad Boat Stringers

    Left unattended, rotted stringers are a death sentence for your boat. Stringers are the longitudinal support beams for your boat's deck, and...

  • How to Repair Pallets

    According to the National Wooden Pallet and Container Association's Uniform Standard for Wood Pallets, "properly repairing and recycling wood pallets is an...

  • Parts of a Cruise Ship

    Parts of a Cruise Ship. Traveling via cruise ships means that you will have the opportunity to enjoy the open seas between...

  • How to Decorate Kitchen Bulkheads

    A kitchen bulkhead is a soffit that juts out over the top of the cabinets. You may be tempted to remove the...

Related Searches

Read Article

10 Delicious Game Day Eats That Rival the Game

Is DIY in your DNA? Become part of our maker community.
Submit Your Work!