There are three reasons your outboard motor's impeller won't pump. The first is that the water stream fitting -- the outlet hole for an outboard motor's cooling system -- is clogged. Insects love to crawl up into it, but once there, they may become trapped and die. Once the cooling system is full of water, with no outlet, the impeller just agitates it, without cooling the motor. The second is that the water inlets are clogged; no water is getting to the pump, so it isn't pumping. Finally, the impeller may be damaged or worn beyond repair, requiring its replacement.
Things You'll Need
- Thin piece of wire
- Garden hose
- Flushing attachment
- Thin-wall socket
- Adjustable wrench
- Pump replacement kit
- Gasket sealer
- Torque wrench
Locate the water stream fitting, found at the rear of the motor, at the bottom of the motor cover. Clear the fitting out out by poking a thin piece of wire into it and pulling any debris or insects out. Check the cooling water intakes and clean them out the same way, if they are clogged.
Connect a garden hose to your motor's flushing point or, if you don't have a single point flushing system, connect the hose to a device called a flushing attachment, and set the flushing attachment over the raw water intakes. Turn the water on, start your motor and warm it to its usual operating temperature. Look at the lower-rear part of your outboard's top cover while it is in operation.
Inspect the water stream fitting once more. If you see a stream of water pouring forth, the impeller is working. Shut the motor down immediately if you do not see a stream of water coming from the lower rear part of your motor's top cover; the problem lies with the impeller, not clogged intakes or a clogged water stream fitting.
Remove the nuts and bolts that connect the lower unit to the rest of the motor with a thin-wall socket. Pull the lower unit away from the motor carefully, lest you bend the driveshaft or shift shaft. The water pump is located on top of the lower unit.
Remove the bolts holding the water pump in place, using an adjustable wrench. Pull the pump cover up and over the top of the driveshaft. Grab the impeller and pull it off the driveshaft just as you did the pump cover.
Insert the new impeller -- from the pump replacement kit -- into the liner of the pump cover. Insert a new gasket in the groove on the underside of the water pump cover and apply a bead of gasket sealer to the gasket. Slide the pump cover and impeller back down the driveshaft and onto the pump's face plate on the lower unit. Bolt the pump cover back in place, tightening the bolts to 60 foot-pounds with a torque wrench.
- "Johnson Repair Manual -- 2.5 to 250 HP Models, 2002-2007"; Seloc Marine; 2007
How to Fix a Mercury Outboard Motor Water Pump
The water pump in a Mercury outboard motor cannot be fixed--it must be replaced, which is not a complicated process. Once familiar...
How to Install a Water Pump in a Mercury Outboard Motor
Putting a new water pump on your Mercury outboard means tinkering with the engine's peripheral workings that, well, keep it working. The...
How to Fix an Outboard Motor Water Pump
Your outboard motor water pump is what pumps water up to the top of the motor from the lower unit. This process...
How to Flush A Mercury Outboard Water Pump
A Mercury outboard engine comes equipped with an internal water pump, which is located in the lower unit. The lower unit is...
How to Change a Water Pump on an Outboard Motor
The water pump on your outboard motor funnels water to the engine to cool it down while it's on. Sometimes, sand and...
What Causes an Inboard/Outboard Motor to Overheat?
Overheating problems in an inboard-outboard motor, also called a "stern-drive," happen as a result of component failure somewhere in the cooling system....
Causes of Overheating in Outboard Motors
Water is critical for a boat's outboard motor to function properly. Water flows through the motor's cooling system using a water pump...
Mercury Outboard Motor Repair Tips
Troubleshooting a problem with a badly running engine, your first course of action is to look into the compression, ignition and fuel...