Over time, the headlight switch on a car can become worn and eventually inoperable. These switches can often be quite expensive to replace. An inexpensive solution is to wire a simple toggle switch in place of the headlight switch, which generally also controls the driving lights. Toggle switches are available at most auto parts stores as well as electronics retailers, such as Radio Shack, and can usually be wired up without too much trouble.
Things You'll Need
- Socket set and ratchet
- Wire cutters
- Wire strippers
- Wire crimpers
- Electrical tape
- Toggle switch
Determine where you want to mount the toggle switch. The switch should be close to the old switch's location so that you can simply run the existing wires to the toggle switch.
Locate the existing wires for the old headlight/parking light switch that you are replacing. Disconnect the wiring harness or wires from the back of the switch. Determine which wires send power to the headlights when the headlight switch is turned on. Consult a workshop manual specific to your car for the wiring diagram if you cannot determine which wires are for the headlights.
Determine how the wires are fastened to the back of the new toggle switch. The back of the toggle switch will have a number of attachment points for wires, which will vary depending on the type of toggle switch you are using. These may be blade type connections or even screw type connections that use a screw to fasten the wire in place.
Fasten the wires for the headlights and the driving lights to the toggle switch. This will probably require cutting the ends of the wires and fastening a blade connector to each end. Use wire strippers to remove about ½ inch of the insulation around the wires then attach the wire connectors onto each wire. Clamp the connector securely around each wire by squeezing it with a pair of pliers then wrap electrical tape around the wires and the ends of the connectors fastened to the wires.
Hook up all of the wires to the connections on the back of the toggle switch. There will be a "ground," a "power" and maybe an "accessory" connection. Hook up the existing headlight wires in the proper order, consulting your wiring diagram for which wire goes where. You can also do this, through trial and error, by connecting the wires until the headlights and driving lights come on when the toggle switch is turned on.
Mount the switch to the dash once the wires have been connected and the driving lights and headlights turn on. The switch can be mounted in a variety of ways. Some are simply screwed on. Others need to be inserted into a hole so that a nut can be threaded onto the back of the toggle switch to hold it in place. Make sure that no metal on the switch comes into contact with any metal on the dash as this can create an electrical short and cause further problems.
Test the headlight switch by turning it on and seeing if the headlights come on. The switch should have three positions: one for off, one for the driving lights and the other for the headlights.
- Photo Credit Hemera Technologies/PhotoObjects.net/Getty Images
How To Wire Lights To a Switch
Lights in a home are typically controlled by a two-way switch. The switch can be turned on, supplying voltage to the light,...
How to Wire a Toggle Switch
A toggle switch is so named because it is a switch with a long handle, or toggle, to control it. A very...
How to Wire Tail Lights
Wiring taillights to your car or truck is not as complicated as some may think. The place where you wire the taillights...
How to Wire a 12-Volt Toggle Switch
Wiring a toggle switch for a 12 volt circuit is a task that even a beginning home handyman can do in a...
How to Wire a Motorcycle Headlight
Converting an off-road motorcycle for street duty requires some extensive electrical work to add on the necessary lighting equipment, with the headlight...
How to Wire a Headlight Switch
Inoperative headlights are often ticketed on sight by law enforcement agencies. Even worse, accidents can occur when headlights fail at an inopportune...
How to Wire in a Headlight Relay
Automotive headlight relays plug directly into a relay socket that comes with wires already attached. If necessary, you can splice and extend...
How to Wire a Mini Toggle Switch
There are many types of toggle switches, but the most commonly used design is a simple SPST switch, or On-Off switch. Activating...
How to Wire 12V Accessories to a Toggle Switch
When wiring a 12-volt toggle switch to an accessory consider a couple of things. Mount the toggle switch in a neutral area,...
How to Wire Headlights to a Toggle Switch to Dim & Brighten
A toggle switch is an ideal dimming switch for use with headlights. By moving the toggle back and forth, metal pins at...