How to Clean a Gun With Kroil


Keeping firearms clean and properly maintained will not only add to their overall lifespan and performance, but can also keep the weapons more accurate and able to hit targets at maximum distances. Kano Kroil is a penetrating oil that has gained a large following for its quality performance when it comes to keeping a firearm in optimum condition. Kroil is adept at getting into the micro-crevices of some of the tougher firing residues found inside of the barrels of firearms and loosens them up to allow for quick and easy removal during the cleaning process.

Things You'll Need

  • Cleaning rod (weapon-specific length and diameter)
  • Bronze bristle brushes (weapon-specific bore sizes)
  • 1 brass patch jag (weapon-specific size)
  • Cotton patches
  • Clean rag
  • Rust preventative compound
  • Copper solvent
  • Kano Kroil oil
  • Unload the weapon and clear the chamber.

  • Attach the bronze bristle brush to the cleaning rod and apply generous amounts of Kroil. Pass the bristle brush through the gun barrel in a back and forth motion for approximately 20 strokes.

  • Remove the bronze bristle brush and wipe the cleaning rod clean with a clean rag.

  • Install the patch jag on the cleaning rod and attach a cotton patch to the jag.

  • Soak the patch in Kroil and pass the jag from the chamber end through the barrel and out the muzzle. Do not pull the jag back through the barrel; allow the patch to fall off once it has breached the muzzle opening.

  • Wipe the cleaning rod clean and attach a new cotton patch. Repeat the previous step until the powder fouling has been removed, wiping down the cleaning rod between each cotton patch. Three passes are generally sufficient.

  • Wipe down the cleaning rod and attach a new cotton patch to the jag.

  • Apply copious amounts of copper solvent to the patch and pass the jag through the barrel, taking care to never pass the jag back through the barrel once the cotton patch has breached the muzzle. Follow up the first cotton patch with a second cotton patch, prepared in the same fashion, immediately after the first pass.

  • Wait five minutes and repeat this procedure until the cotton patch no longer has a blue/green color (copper residue) when it exits the muzzle.

  • Wipe down the cleaning rod and attach a dry cotton patch.

  • Pass two or more dry cotton patches through the barrel, using the same techniques as before, to remove any traces of the copper solvent.

  • Wipe down the cleaning rod and attach a new cotton patch with a rust preventative compound applied and pass it through the barrel according to the manufacturer's instructions.

Tips & Warnings

  • The last step is only necessary if the weapon will be in storage for a long period of time without being fired.
  • Never leave the copper solvent in the barrel for more than four minutes to avoid pitting and other serious damage. The drying step of the cleaning process will help avoid leaving solvents in the barrel and should be done with attention to detail.

Related Searches


  • Photo Credit rifle image by petar Ishmeriev from
Promoted By Zergnet


You May Also Like

  • What Is Penetrating Oil?

    If you are an auto hobbyist, young machinist, do-it-yourselfer or avid tinkerer, you might have heard the term "penetrating oil." Penetrating oil...

  • How to Buy Kroil

    Kroil is an industrial-strength penetrating oil made by Kano Laboratories. According to the company, Kroil loosens frozen metal parts by penetrating into...

  • How to Clean a Rifle With Hoppes Products

    Properly cleaning your rifle is an important part of being a gun owner. Metal and powder fouling build up after every shot,...

  • Gun Cleaning Solvents

    The type of gun-cleaning solvent that a person should use is dependent on the type of ammunition they use in their gun....

  • How to Clean a Gun

    Whenever a gun is being cleaned, make sure it's empty, unloaded and that the ammunition is in another room. Clean a shotgun,...

Related Searches

Check It Out

How to Build and Grow a Salad Garden On Your Balcony

Is DIY in your DNA? Become part of our maker community.
Submit Your Work!