How to Skin a Fox Fur

Save

Fox furs, or pelts, as the dried furs are commonly referred to, hold their value year-to-year and so are worth the trapper and hunter’s efforts to obtain them. Once a fox is taken, the first step is to skin the fox properly to make sure the pelt arrives at the fur buyer in perfect condition. The skin of a fox is thin and easily damaged or torn, so it is necessary to proceed carefully when skinning. A small pocket knife with a narrow three-inch blade is the best choice for skinning a fox.

Things You'll Need

  • Pocket knife
  • Rubber gloves – snug fitting
  • Cord
  • Tie a length of cord to each hind leg of the fox, just above the foot; tie the opposite ends of the cords to a rafter or anything that is above your head. Lower the fox, head down, until the hind legs are at eye level and pull the hind legs as far apart as they will go.

  • Put on the gloves. Cut through the skin just above each foot, front and hind legs, going completely around each leg in a circle.

  • Stick the tip of the knife into the cut on one back leg and cut an incision following along the back of the leg, just below the anus and along the back of the opposite leg ending up at the cut around the foot.

  • Cut around the anus and then poke the tip of the knife into the incision between the anus and the tail. Slice an incision on the underside of the tail half way to the tail’s tip.

  • Peel the skin away from the tail bone with your fingers until the skin is free from the tail bone for the length of the incision. Push your fingers against the fur part of the tail at the end of the incision. Pull the remainder of the tail bone in the opposite direction, sliding it out of the uncut part of the tail.

  • Pull the skin away from the carcass at the hind legs and cut through the membrane holding the skin to the carcass. Keep skinning out the hind legs until the skin is free of the legs.

  • Slide the thumbs and forefingers of both hands between the skin and carcass and peel the skin down the body until the front legs are reached.

  • Pry the skin away from the upper part of the front legs with your fingers only, as a knife here can cut the skin. For each leg, push a finger through the opening made between the leg and freed skin, grip the leg and pull it toward the body while pulling the skin over the leg in the opposite direction. Pull until the skin comes free over the foot.

  • Skin down the neck to the ears using caution not to cut into the neck arteries. Cut the ears free by cutting against the skull and through the cartilage at the base of the ears.

  • Move the knife slowly, skinning down the face to the eyes. Press the knife blade against the eyes cutting through the membrane covering the eyes, being careful not to cut the skin around the eyes.

  • Pull and cut the skin free down the muzzle to the nose. Cut through the nose cartilage, freeing the nose. Cut the lips free by passing the knife between the skin and jaw bones. The skin is now free of the carcass and ready to be stretched and dried.

Tips & Warnings

  • Much of a fox’s skin can be peeled off the carcass by hand. The skin over the face and around the hind legs will need to be cut free; cut slowly through the membrane holding the skin to the carcass.
  • In years past the feet were left on a fox skin as that was the demand of the market. Today, it is preferred by fur buyers to not have the feet on the pelt.
  • Cutting the arteries in the neck will release the blood which will run into the fur. This can be avoided by not pressing the sharp edge of the knife blade against the throat.
  • Wear rubber gloves for skinning to protect you from any health-related problems the fox might have had.
  • Pull the skin away from the carcass while skinning; do not cut near your fingers.

References

  • “Trapping North American Furbearers;” S. Stanley Hawbaker; 1969
  • Photo Credit Tom Brakefield/Stockbyte/Getty Images
Promoted By Zergnet

Comments

You May Also Like

  • Fox Terrier Skin Problems

    The fox terrier is a delightful breed of dog. Fox terriers are energetic, playful and can be very loyal pets. The breed...

  • How Do I Change My Firefox Skin?

    Skins change the appearance of your Web browser. In Firefox, skins are called “themes.” There are two types of Firefox themes: background...

  • How to Skin a Squirrel

    Learn how to skin squirrels like a professional, once the squirrel hunt is over. The skinning is probably the easiest part of...

  • How to Skin a Bobcat

    Skinning a bobcat requires a steady hand and basic knowledge of the animals' anatomy. The bobcat is a small cat, typically weighing...

  • How to Dye Fox Fur

    Standard fur garments bring a regal look to most occasions. Nature’s beautiful browns, creams and tans add a wonderful sophisticated look to...

  • How to Skin a Raccoon in Fur Trapping

    The sale value of a raccoon pelt depends on how well you skin and prepare the pelt. Fur buyers pay top price...

  • How to Tan a Fox Fur

    Tanning furs will bring a great look to your fur and will preserve them since you have likely spent a great deal...

  • How to Make a Mountain Man Fox Hat

    Wearing a fox skin hat as worn by the mountain men of long ago can make anyone feel like they can take...

  • How to Clean Fox Fur

    Fox fur is usually in the form of a mounted pelt, a garment or on the back of a taxidermied animal. Cleaning...

  • How to Taxidermy a Fox

    Whether you are preserving a fox from your latest hunting foray or creating a valuable new specimen for a museum collection, small-game...

  • How to Skin a Gray Fox for Taxidermy

    The basic method for skinning an animal for the purpose of a life-size mount is to begin with a single incision along...

  • How to Tan Fox & Raccoon Pelts

    Fox and raccoons have beautiful pelts that can be made into a variety of clothing and accessories; the pelts can also be...

Related Searches

Check It Out

How to Build and Grow a Salad Garden On Your Balcony

M
Is DIY in your DNA? Become part of our maker community.
Submit Your Work!