Front-end loaders carry, lift and deposit loose materials: sand, soil, stone, quarry slag, coal, ore and many other similar loads. The front-end loader needs tremendous power to lift and tilt the bucket located at the end of two long arms. A powered hydraulic system (or circuit) provides the necessary power to lift not only the load, but also the weight of the bucket and arms. When there are problems with the hydraulic power, there are three main components to inspect for trouble: the hydraulic pump, the high-pressure hydraulic lines and the hydraulically actuated piston.
The hydraulic pump on a front-end loader is located either in the forward area of the engine bay or under the driver's compartment. The engine produces electrical power to operate the pump. Hydraulic pumps must be completely sealed and leak free; copious amount of puddle hydraulic fluid could mean the seals around different fitting are no longer tight. Also, the pump assembly has a large canister attached for the hydraulic fluid filter. Changing the filter regularly is a must to maintain optimum power in the hydraulic circuit.
A front-end loader has different movable parts where the hydraulic lines must connect. A combination of hard annealed steel tubing and high-pressure rubber hoses carry the hydraulic fluid to the piston, then low-pressure lines return the fluid to the pump. Make sure all the lines are leak-free. Moving hoses are especially susceptible to chafing getting crimped. Check the hoses for shiny areas where constant chafing is smoothing the surface--these areas can indicate a future trouble spot. Try to pad or protect the hose section from further damage.
The hydraulic lines are connected at each end with stainless steel high-pressure fittings. Make sure all fittings are tight and leak-free. If a fitting does fail, do not try to repair it--it must be replaced. The pressure hydraulic circuits endure almost guarantees any fix will fail quickly.
The hydraulic piston does the work; slow and intermittent piston action is the most obvious indicator of hydraulic circuit problems. Front-end loaders may have up to eight pistons (four on each side) actuating the lift arm, the bucket, a pivot point (so the loaded bucket can turn) and side support legs. Prevent contaminating material from getting into the piston and cylinder assembly with tight seals. If pistons begin to lose responsiveness to controls it could mean a hydraulic pressure loss because of leaky hoses, fittings or seals. Also, any dents or corrosion in the piston and cylinder can cause hindered action. Repair or replace any such damage immediately.
- Photo Credit loader 1 image by Jim Parkin from Fotolia.com
Specifications for a John Deere 300CX Loader
John Deere engineers designed the 300CX front-end loader to fit a wide range of its compact tractor models. The 300CX fits several...
Bulldog Front End Loader Information
Small and mid-size tractors are indispensable pieces of equipment for owners of hobby farms and large rural properties. Implements and attachments, such...
How to Troubleshoot a 1999 John Deere Skid Steer
The John Deere skid steer comes in three types of models: under 50 horsepower, 50 to 75 horsepower and over 75 horsepower....
How to Repair a Kubota Front-End Loader LA272 for a B7510
The Kubota B7510 tractor series is designed for landscaping and light construction work that requires a horsepower of between 18 and 32....
How to Attach a Loader to a John Deere Tractor
Virtually every model John Deere utility tractor produced from the 1950s forward has the option to add a loader. Many loader models--particularly...
How to Dig a Hole with a Front End Loader
Using the power of a front end loader to dig a hole can save hours of time in manual labor. The front...
How to Rebuild a Kubota Hydraulic Cylinder
Kubota manufactures tractors, mowers and light to medium-duty construction equipment. Several of their vehicles have moving parts, such as scoops or buckets....
How to Connect a Hydraulic Cylinder to a Tractor Loader
A tractor loader can add versatility to a tractor and can be installed on the front or rear of it. A tractor...
Mustang Skid Loader Specifications
Mustang has been manufacturing Skid Steer Loaders since 1965. They have since produced several lines of Skid Steer Loaders and continue to...
Problems With Front-Loader Washers
Front-load washers are appealing for their water efficiency and washing capabilities and are the popular choice for washing machine replacement when top-loaders...
Bobcat Loader Troubleshooting
Bobcat is one of the leading manufacturers of skid-steer loaders and has steadily improved its products over more than 50 years. The...
How to Use a John Deere Loader SCV Lever
Most John Deere utility tractors produced from the mid-90s forward include a dual function selective control valve (SCV) lever, commonly called a...