How to Bend Oak Without Steam

Save

Bent oak looks exotic, and seems to defy nature. You can bend oak into almost any shape you want without steaming it. Woodworkers know a trick that involves cutting the oak into thin pieces first, then gluing them around a form to bend them. Bending your own oak this way lets you create any bent oak radius you desire, and you can do it in one afternoon.

Things You'll Need

  • Compass
  • Plywood, 3/4-by-24-by-24 inches
  • Bandsaw
  • Jigsaw (optional)
  • Oak lumber, 3/4-by-3-by-36 inches
  • Table saw
  • Wood glue
  • Hand clamps
  • Cut the plywood into the letter "C" using your bandsaw. Use a compass to round the corners. Keep the plywood as close to the 24-by-24 inch size as possible. If you don't have a bandsaw or are not qualified to run one, use a jigsaw.

  • Set the table saw at 3/16 inch and cut the board into lengthwise strips.

  • Lay the "C" form out on a flat surface. Lay one of the strips down on its edge on the curved side of the form. Spread glue along both sides of another strip and lay it down beside the first strip. Set another strip down beside the glued one to form a sandwich with glue in the middle, and dry edges on both outer edges.

  • Reach over the center of the "C" and the strips with a clamp. Tighten the clamp against the strips and the center of the "C" form. Place two more clamps on either side of the first clamp and tighten them. Continue around the form placing the clamps every 6 inches. Let the glue dry for one hour.

  • Remove the clamps and place a glued strip. Follow that with another glued strip and then another dry strip. Place clamps around the form as in Step 4, on top of the original strips. Wait one hour for the glue to dry. Remove the clamps and glue up another strip sandwich. Clamp, and repeat until all the strips are used up or you have reached your desired depth.

  • Remove the clamps the final time. You now have a bent piece of oak that you can use for arch molding or a custom woodwork project.

Tips & Warnings

  • Sand the glue off with 100-grit sandpaper and cut the bent oak on the bandsaw to fit anything you desire. The measurements here are examples only. You can make your form any size you want.
  • Lay a piece of plastic underneath your form to prevent glue from dripping when you clamp your oak to the form.
  • Always wear safety glasses when working with wood.

Related Searches

  • Photo Credit Jupiterimages/Photos.com/Getty Images
Promoted By Zergnet

Comments

You May Also Like

  • How to Bend Wood to Make Furniture

    Craftsmen have used wood-bending techniques to make furniture for centuries. Bent wood is used to make the backs of chairs, banisters and...

  • How to Bend Wood With Heat

    Wood is a very durable material that can withstand many years of use and is not easily bent. You can prepare the...

  • How to Make a Steam Box to Bend Wood

    Many wood projects require bent wood. The techniques are commonly required in boat building but can be useful in many other types...

  • How to Bend Wood Trim

    Bending wood is not magic. Wood will bend if its cut it the right places or cut thin enough. There are several...

  • How to Bend Oak Wood

    Oak is a hardwood used in a variety of applications, from floors to furniture. Because it's so hard, working with it requires...

  • How to Fix Warped Oak Boards

    Boards that bend and twist can be nearly impossible to build anything with. Worse yet is the board that waits until it...

  • How Can I Bend 1/4" Plywood?

    Plywood is a wood composite material made of thin layers of wood veneer glued together into a panel of consistent thickness. It...

  • How to Make a Bent Wood Ring

    You can bend wood into a complete circle. The trick is to start with thin pieces. Bent wood chair manufacturers do it...

  • How to Bend Wood to Make Furniture

    Bend wood to make furniture using a bent lamination technique that involves cutting wood into the desired shape, ripping wood strips, applying...

Related Searches

Check It Out

DIY Wood Transfer Christmas Ornaments

M
Is DIY in your DNA? Become part of our maker community.
Submit Your Work!