Welding cast iron can be challenging if you do not know the correct process and the properties of the metal. Cast iron contracts and expands with temperature all the time. Cast iron has brittle properties that allow it to crack easily, and it rusts easily. Several kinds and grades of cast iron exist, making it difficult to know its carbon content. However, cast iron can be successfully welded with a gas welder, called an oxyacetylene system, along with some special welding rods and proven welding techniques.
Things You'll Need
- Drill motor
- Conical grinding bits
- Safety goggles
- Wire brush
- Old barbecue (optional)
- Welding hood
- Oxyacetylene welding system
- Respirator (optional)
- Hydrochloric acid (optional)
- Tinning flux
- Flux brush
- Braze welding rod (copper alloy filler)
- Slag hammer
Place the cast iron piece on a firm bench, in a vise or on the floor. Make certain that no combustible materials are within range of any sparks produced from grinding. Place a conical, pointed grinding bit in a drill motor. Don gloves and safety goggles. For a crack or break in the stock iron piece, turn the drill on and grind out a V-groove channel inside the crack until you have removed all rust and reached bare, shiny metal.
Grind the outside edges of the crack area for at least two inches on all sides. There should be nothing but bare, shiny metal showing. Inspect the ground-down area for pits or holes in the iron. You might see small pressure cracks. For iron in this condition, move the piece to a well ventilated area outside. Don a respirator and pour a few ounces of hydrochloric acid on the crack and move away from it. Let it air dry.
Place the cast iron piece over a metal plate that rests over a solid surface made of cement or bare earth. Or use a vise to secure it, if the area contains no combustible materials. If the stock piece can fit inside an old barbecue, place it there on top of the grille.
Don a welding helmet. Turn your oxyacetylene welding set valves on and ignite your welding torch. Adjust the flame for a neutral dispersion. Preheat the iron piece with the torch, bringing the surface to a dull red color. Move the flame away and wire brush the crack area.
Heat the iron piece up with the torch again until dull red. Use a flux brush to paste flux over the crack area, inside and out. Adjust the oxygen setting on your welder to produce slightly more oxygen flow to the tip flame. Place a braze welding rod into the crack area at one end, while holding the torch on the tip of the rod.
Let the rod melt and flow into the crack area. Push the bead of melted rod along the crack. Stop after a few inches. Pull the torch tip away and gently tap the bead with a slag hammer. Let the piece cool completely.
Heat the iron piece again until it glows dull red. Paste more flux on the crack. Insert your welding rod over the crack where you left off. Run another two-inch bead of weld over the crack. Tap with the slag hammer. Let it cool. Continue to weld two-inch sections in this manner until you have reached the end of the crack. Tap the bead weld with the slag hammer and use the wire brush to burnish away any ash. Let the piece cool and inspect the weld.
- Photo Credit welding image by glgec from Fotolia.com
How to Weld Cast Iron
How to Weld Cast Iron. Cast iron usually has a carbon content of 2 to 4 percent which is much greater than...
How to Braze Cast Iron
Brazing cast iron is not too difficult with practice but there are a few gotcha' s that will cause problems if you...
How to Weld Cast Iron With a Wire Feed Welder
Welding on cast iron is a bit different than welding on most other metals. Because of its chemical makeup, cast iron is...
How to Repair Cast Iron With Putty
Cast iron is a useful material that is used in a variety of ways from stoves to engines. It is a hard...
How to Repair a Cast Iron Crack Without Welding
Cast iron is used in many household and industrial structures. Cast iron is by nature brittle and can be susceptible to cracks...
How do I Purge a Pipe for TIG Welding?
Purging a pipe involves inducing an inert gas into the pipe to remove reactive atmospheric gases from the welding area. An inert...
How to Glue Cast Iron Together
Cast iron's hard, nonmalleable qualities make it a powerful metal for household objects ranging from garden fixtures to cookware to decorative ornaments....
How to Use Welding Safety Equipment
Learn about welding safety equipment in this free educational video.
Exhaust Manifold Repair Techniques
Many vehicles come with cast iron manifold stock. This material is generally fairly reliable, but does have some problems. Cast iron manifolds...