Windows are our eyes onto the outside world. They allow light and air to come into our living and work spaces and provide security by allowing us to see what's outside without exposing ourselves to unnecessary danger. Adding windows to pole barns is simply a matter of adding the frame work required to support the window frame. Since building codes do not typically apply to pole barns, you will be responsible for making sure the window is safely and securely mounted.
Things You'll Need
- Tape measure
- Mason's twine
- String level
- 2 by 4 lumber
- Circular saw
- Pole end
- Treated deck screws
Measure up from the ground and mark the pole to the left side of the window installation area at a point 1/2 inch below where the bottom of the window jamb will be installed and 1/2 inch above the top. Use a piece of mason's twine and a string level to stretch across from each mark to the pole on the right side of the installation area and mark the post so that it is level with the marks on the left post.
Measure the distance between the bottom and top marks. Cut a 2 by 4 so that it is 1/2 inch longer than the distance between the poles at each point. Trace a curve that is the same radius as your barn poles using the end of a pole that is the same size as your barn poles. Trace the curve onto the wide face at each end of each 2 by 4 so that it is 1/4 inch in from each end. Cut the curves with a jigsaw.
Fit the 2 by 4's between the poles with the top face of the bottom board even with the mark and the bottom face of the top board even with the mark. Check both boards with a level and adjust as needed to center the bubble in the indicator. Measure the distance between both boards at each post and adjust as needed to make them equal.
Drive two 3-inch treated deck screws up at an angle through each end of each 2 by 4 into the poles, holding them firmly to prevent shifting. Find and mark the center from pole to pole on each board with a tape measure. Measure from this point and mark a distance one-half the width of your window from outside to outside, plus 1/4 inch. Mark a straight line on the two outside marks on the top and bottom boards with a rafter square.
Measure and cut two 2 by 4's to fit between the top and bottom horizontal 2 by 4's. Align one with each of the marks on the horizontal 2 by 4's so that the inside face of the board is aligned with the line. Drive two 3-inch treated deck screws up through the bottom 2 by 4 and down through the top 2 by 4 into the ends of the vertical 2 by 4's.
Drill through the siding to the outside in each corner of the window opening to mark the position of the frame. Draw lines connecting the four corner holes on the outside of the barn siding. Use a circular saw to cut the opening along all four edges. Drive screws through the siding into the 2 by 4 frame, placing two screws on each side of the window opening.
- "The Complete Guide to Building Barns and Outbuildings A Step-by-Step Guide"; Atlantic Publishing Company; 2009
- "Building Small Barns, Shed & Shelters"; Monte Burch; 1983
- Photo Credit barn 6 image by michael langley from Fotolia.com
How to Install Windows in a Pole Barn
Windows also provide less of a shed or barn feeling to your construction, and expands the potential uses of the structure into...
How to Install a Soffit in a Pole Barn
The soffit covers the underside of your barn roof's overhang, seals off the roof from drafts and keeps out bats and other...
How to Frame a Pole Building
Framing a pole building is a straightforward process that requires very little building experience. Armed with the proper tools and supplies, you...
How to Frame a Pole Barn
Attach 2-by-6 fpot lumber with screws horizontally on the outer side of the poles, spacing each row two to three feet apart....
How to Design Your Own Pole Building for Free
Pole buildings have been around for a long time due to their ease of construction, low cost and wide variety of uses....
How to Build Pole Barn Doors
Pole barn doors can add to your convenience, especially when moving heavy equipment or other large items into your pole barn. There...