How to Build Metal Drawers

Save

Metal drawers are handy items to have in any work space, from an office to a metal or woodwork shop. They are expensive to buy yet relatively inexpensive to make, so if you have the right materials at hand, there is no reason you shouldn't make your own.

Things You'll Need

  • Sheet metal
  • Cutting torch
  • Arc welder
  • Chalk
  • Measuring tape
  • 1-by-12-inch metal rods (4)
  • Metal cabinet handles
  • Design the drawers on paper. Design one large sheet-metal box and three separate drawers that fit into it. Start with a box that's 2 feet wide and 3 feet high and 2 feet long. The individual drawers should be 2-by-2-feet square by 11 inches high.

  • Mark the sheet metal with the desired dimensions. For the large box, use two 2-by-2-foot pieces of sheet metal for the base and top and three 3-by-2-foot sheet metal pieces for the sides. Leave the front open to install the shelves. Each shelf should have one 2-by-2-foot sheet and four 2-foot-by-11-inch sheets.

  • Cut the individual components out of the sheet metal using a cutting torch, angle grinder or power jigsaw. Be careful to follow the lines precisely so as not to cut away too much. A good rule of thumb is to cut away too little rather than too much -- you can always trim later.

  • Weld the large metal box together using an arc welder. Weld the upright pieces to the base. Then weld the top onto the upright pieces.

  • Weld the drawer pieces together. Weld four 2-foot-by-11-inch sheets to the edges of a 2-by-2-foot base. Repeat with the other two drawers.

  • Weld 1-by-12-inch metal rods onto the inside of each side of the large metal box. These should be welded at 1-foot intervals, starting 1 foot from the base. These will hold the drawers in place.

  • Weld handles onto the front of the drawers. Measure the exact central point of the front of each drawer. To find the center, measure the width and height, then divide each number in half. Extend your tape measure to the new numbers and mark the location with chalk or pencil. Weld the handles in the center of the drawer fronts.

  • Slide the drawers into the large metal box.

References

  • Photo Credit drawer image by Jan Will from Fotolia.com
Promoted By Zergnet

Comments

Resources

You May Also Like

  • How to Disassemble Metal Drawer Slides

    Sometimes your old metal drawer slides can become broken or bent, rendering your drawer unusable. You can disassemble the old drawer slides...

  • How to Make Wood Drawer Slides

    A drawer slide has three parts: a slider and two bars. Mounting the slider on the drawer reduces the leverage on the...

  • How to Build Drawers

    Drawers are about as handy as a pocket on a shirt. One set back experienced by consumers is the drawer space that...

  • How to Build Cabinet Doors & Drawers

    When entering a kitchen, one of the first things that catch the eyes is the cabinet doors and drawers. The more elaborate...

  • Materials Needed to Make a Flagpole

    The materials required to make a flagpole differ depending on the application. In-ground flagpoles are designed to withstand wind and direct exposure...

  • How to Make Cabinet Drawers

    The key to making cabinet drawers is first to determine the roller assembly you want to use. Some don't require much of...

  • How to Bend a Sheet Metal Flange

    Standard sheet metal flanges are used for mounting accessories to duct work. Sheet metal flanges can be bent to any size, but...

  • How to Make a Sheet Metal Box

    Metal lock boxes can be used for a variety of tasks, from storing ammunition to hauling cargo over rugged terrain or even...

Related Searches

Read Article

How to Make a Mid-Century Modern Inspired Fruit Basket

M
Is DIY in your DNA? Become part of our maker community.
Submit Your Work!