How to Make a Gas Can Guitar

Save

The gas can or oil can guitar is a funky contribution from African culture; African musicians who couldn't afford a guitar built their own from squared metal cans and whatever wood they could get their hands on. Gas can guitars are prized for their funky chic and their raw, metallic sound. Building one is not nearly as difficult as building a wood guitar, especially if you use parts salvaged from old electric and acoustic guitars.

Things You'll Need

  • Metal gas or oil can, 10 quart size
  • Bolt-on neck from an electric guitar
  • Bolt plate from guitar neck
  • Bolts from guitar neck
  • Tin snips
  • Rotary tool with grinding bit
  • Length of maple board, 2 1/4 inches by 3/4 inches by 13 inches
  • Length of maple board, 2 1/4 inches by 3/4 inches by 4 inches
  • Power drill with 1/4-inch bit
  • Pencil
  • 4 flat-head machine screws, 1/4-20, 2 inches long, with matching hex nuts
  • Small carpenter's square
  • Pliers or adjustable wrench
  • Screwdriver
  • Piece of ebony, 1/2 inch by 1/2 inch by 4 1/2 inches
  • Disk sander
  • Needle file
  • Tape measure
  • Remove the neck from the electric guitar by unscrewing the four bolts that hold it on. Save the bolts and the bolt plate from the back of the guitar.

  • Wash the can thoroughly with water and an antigrease detergent; rinse and allow to dry.

  • Cut away the handle of the can, particularly if it is in the center of the can's top.

  • Decide which side of the can you want to face front. Cut a hole in the top of the can, flush with and in the center of the front edge. The side of the hole flush with the front edge should be about 2 1/4 inches wide, and the hole should be about 2 inches deep. Smooth the sharp edges with the rotary tool and the grinding attachments.

  • Trace four holes on one end of the the 4-inch length of maple, using a pencil and the bolt plate from the electric guitar neck as a template. Drill 1/4-inch holes at the four pencil marks. Repeat this process with the other side of the wood.

  • Screw the guitar neck bolts through four of the holes in the 4-inch length of maple, and into the back of the guitar neck.

  • Slide one end of the 13-inch length of maple between the fingerboard of the guitar neck and the piece of wood bolted onto it. Make sure the maple is lined up straight with the neck, and trace the four remaining holes in the 4-inch length onto the end of the 13-inch length of wood. Drill 1/4-inch holes at the pencil marks.

  • Turn the neck assembly over so the fingerboard is facing up. Bolt the 13-inch length of maple onto the neck assembly by inserting four bolts through the holes in the end of it, then through the four open holes in the 4-inch length of maple. Attach with hex nuts and tighten so that the bolt heads are flush with the front of the wood.

  • Insert the neck assembly into the hole in the top front of the can. The fingerboard should go outside the can, and the 13-inch length of maple should be flat against the inside surface of the front of the can. Use the carpenter's square to make sure the neck is at a right angle to the upper edge of the can, then drill two 3/32-inch holes through the front of the can and into the wood behind it. The first hole should be just under the bottom edge of the fingerboard, and the second should be about 2 inches up from the bottom of the can. Insert wood screws into these holes and tighten them.

  • Attach the tailpiece by driving three screws through the holes in the short angled section of the bridge, through the bottom of the oil can and into the wood of the neck assembly.

  • Shape the piece of ebony into a triangular wedge 1/2 inch across the bottom and 1/2 inch high at the peak. This will be the bridge. File six small slots into the peak of the bridge to hold the strings; the slots should start at 1 1/8 inch from each end of the bridge and be spaced about 1/2 inch apart.

  • Measure the distance on the guitar neck from the bottom edge of the nut (the white part under the head that holds the strings) and the 12th fret. Measure this same distance from the 12th fret down toward the tail piece. Place the bridge at this point on the top of the can.

  • String the guitar by running each string through the hole in the tailpiece, over a slot on the bridge, over a slot on the nut, and into the hole in the soundpost of a tuning machine.

Related Searches

References

  • Photo Credit Jupiterimages/Photos.com/Getty Images
Promoted By Zergnet

Comments

You May Also Like

  • How to Build an Oil-Can Guitar

    The first oil-can guitars were made in Africa and were called ramkiekies. Today these are still the first instruments many folk musicians...

  • How to Build a Guitar Amp

    It is possible to build your own guitar amp and save a lot of money doing it. You can get the same...

  • How to Make Acoustic Guitars

    Playing an acoustic guitar can be a true art form. To make the guitar sing takes real talent. Making acoustic guitars, however,...

  • How to Make a Soda Can Guitar

    You've seen guitars made out of wood and you may have seen some guitar-type crafts made out of a shoebox. You probably...

Related Searches

Check It Out

12 Tiki Essentials to Turn Your Bar Cart Into a Tropical Paradise

M
Is DIY in your DNA? Become part of our maker community.
Submit Your Work!