If you have an Epson printer and get an error message reading: "The printer's ink pads are at the end of their service life," it may well mean that your ink pads are full and need to be changed. In the process of printing, the printer produces waste ink that has to go somewhere. It is sent through a tube to the ink pad, where it is collected. The printer has a counter that initiates the above-mentioned error message once a certain number of pages have been printed. According to the Epson manual, you need to take the printer to be serviced and may even need to replace the whole printer. That said, you can choose to fix the problem yourself if you want to save money.
Things You'll Need
- Phillips head screwdriver
- Flat head screwdriver
- Plastic table cover
- Plastic tubing
- Needle nose pliers
- Airline connectors
- Paper towels
- Rubber gloves
Spread plastic or newspapers over a table and place your unplugged printer on it.
Remove the viewing panel. This is a panel on the back of your printer on the right side, held in place by one or two screws. On some printers, it will be a rectangular panel, and on others the whole right side of the printer will come off. Locate the screws, and using a Phillips head screwdriver, remove them. With a flat head screwdriver, carefully pry the panel off.
Find the ink waste tubes. These should be easy to locate because they will be two clear tubes running side by side into the ink waste reservoir. Some printers will only have one tube. One end of the tubes will be attached inside the printer and the other ends will be loose. Pull the loose ends of the tubes through the panel opening so they are hanging out. You may need to use needle nose pliers to accomplish this if you cannot easily grasp the tubes with your fingers.
Remove the old pad. This is a messy task, so make sure that the area surrounding the printer is covered with material that you don't mind getting ink on. You may wish to wear rubber gloves. Using the pliers, pull the pad out of the printer and set it aside. Clean out the reservoir by pushing paper towels into it and letting them soak up the ink.
Replace the pad. You can purchase a clean pad at a computer parts store, but they can be hard to find and expensive. You can also cut a new dish sponge to the proper size and insert it as a replacement. You may also try cleaning the old pad by letting it soak in a large bowl of hot water then squeezing it out. Make sure it is completely dry before putting it back in the printer. Place the loose ends of the tubes back into the reservoir the way they were. Most people, however, choose to make an external ink waste reservoir. To do this you will need to extend the tubes. This can be done by purchasing air line connectors and some plastic tubing to fit. These items can be purchased inexpensively wherever aquarium supplies are sold. If your printer has two tubes, cut two one foot long pieces of tubing. If it only has one tube, just cut one piece of tube. Insert the connectors into the ends of the tubes attached to the printer then connect them to the tubes you just cut. Then punch a hole in the cap of a bottle and insert the ends of the tubes down into it. A small, plastic water bottle will work fine. Now the waste ink will flow into the bottle and you can empty it any time you need to. You may want to attach the bottle to the side of the printer using Velcro or tape so it does not tip over.
Reset the counter and get rid of the error message. To do this you will need to download software. You can download it for free at ssclg.com. The link is in the resources. Run the program on the computer connected to the printer. It will allow you to reset the counter to zero and dismiss the error message. It is a good idea to read the instructions in the help file of the program before doing anything. However, once the program is downloaded, it will appear on your desktop tray and you can right-click it to bring up a menu of options. The second option is "Reset counters." Click on this to reset your counter and thus cancel the error message.
Tips & Warnings
- If you choose to make the external reservoir, you can skip removing the pad if you wish, and leave it as it is as you will be bypassing it.
- Making modifications to your printer can nullify any warranty you have on it.
- Generally, you will receive the error message at around 10,000 prints, so if you get it after making significantly fewer prints than that, you should consult Epson before doing anything to your printer.
- Photo Credit Hemera Technologies/Photos.com/Getty Images
How to Replace the Waste Ink Pad on a Epson CX5400 Printer
Printers, such as the Epson CX5400, come with waste ink absorber pads which are created to catch excess ink and avoid damaging...
Directions to Change the Cartridge in an Epson Printer
Now, more recent models such as the Artisan 800 have streamlined the refilling process, ... How to Replace the Ink in an...
How to Reset the Ink Levels on an Epson
Life Skills Gadget Guide. eHow; ... and change the waste ink pads (technical service). ... "The printer's ink pads are at the...
How to Troubleshoot an Epson Inkjet Printer
Epson inkjet printers are relatively easy to repair and troubleshoot. ... Life Skills Gadget Guide. ... The printer's ink pads are nearing...
How to Change the Ink Pad on a Self Inking Stamp
Life Insurance; Retirement. Get Started; Plan Ahead; Make It Last; Investing. Building Wealth; Balancing a Portfolio; ... "The printer's ink pads are...