The GMC Yukon comes in a few different packages with a variety of options. Available in two-wheel or four-wheel drive, it also features an upgraded version of the Yukon Denali and the Yukon XL. The most popular Yukons came in the 1500 series (quarter-ton) with a front and rear shock absorber suspension. The front of the SUV employed a coil spring to suspension, and the rear used a leaf spring suspension.
Things You'll Need
- Wheel block
- Wheel nut wrench
- Service jack
- Jack stands
- Penetrating lubricant spray
- Box-end wrench set
- Ratchet and socket set
- Replacement shock absorbers
- Torque wrench
Place a wheel block behind the rear tires and apply the parking brake.
Loosen the front wheel nuts with a wheel nut wrench (no more than a half turn), hoist the front of the Yukon up with the service jack and then place a jack stand under the lower control arm. Finish removing the wheel nuts and then remove the wheels.
Place a box-end wrench onto the upper shock mounting nut, and then hold the stem of the shock with another box-end wrench (smaller) or a ratchet and socket. Loosen the upper mounting nut by turning it counterclockwise while holding the stem. You will need to remove the wrench from the mounting nut to reposition it for room every half turn or so.
Remove the two lower mounting bolts and nuts on the shock absorber using a wrench to hold the head of the bolts, and a ratchet and socket to remove the nuts.
Remove the shock. On two-wheel drive models, the shock is placed inside of the coil spring, so it will drop down from inside the coil spring through the lower control arm. On four-wheel drive models, it is separate from the coil spring and has its own mounting plate at the top of the frame, and the bottom is bolted to the lower control arm.
Reverse the procedure to reinstall the shocks. Be sure to replace the upper bushings and washers (equipped with the replacement shocks) correctly onto the stem. Install the lower washer and bushing onto the stem before installing the stem through the upper shock plate. Then place the upper bushing and the upper washer onto the stem before replacing the upper mounting nut.
On two-wheel drive models, torque the upper retaining nut to 12 foot-pounds and the lowers to 25 foot-pounds with the torque wrench and a socket. On four-wheel drive, torque the upper and lower mounting nuts to 66 foot-pounds. Replace the wheels and torque the lug nuts to 120 foot-pounds. Some later models may require a higher torque specification.
Place the wheel wedge in front of one of the front tires, then loosen the rear wheel nuts as illustrated in Section 1.
Hoist the rear axle and set the jack stands beneath the rear axle itself, making sure not to get too close to the lower shock mounts. For added safety, place the cup of the service jack below the rear differential and lift the jack cup just high enough to touch the bottom of the differential.
Spray the mounting bolts (upper and lower) with a copious amount of penetrating lubricant and allow it to soak in for five to 10 minutes.
Hold the bolt heads with a box-end wrench, remove the mounting nuts from the upper shock mount, then the lower shock mount. Remove the shocks. Remove and replace one side at a time so you do not overstress the rear leaf springs with the weight of the rear axle with the truck elevated.
Replace the shocks by reversing the removal installation. Tighten the upper and lower retaining nuts to 60 foot-pounds. On some older versions of the Yukon, the upper shock may be connected to the frame with two small retaining bolts instead of one shock eyelet bolt. Tighten these two small bolts to 20 foot-pounds if applicable.
Tips & Warnings
- For Yukons equipped with selectable ride, disconnect the real time damping (RTD) link rod from the sensor prior to removing the upper mounting nut. Grasp the upper and lower connector lock tabs (at the top stacked on top of each other), then rotate the connector lock tabs counter-clockwise until the connector is unlocked. Disengage the connector from the stem by firmly pulling the connector up. Hold the stem end with a wrench while removing the mounting nut. Do not discard the plastic upper pilot ring as it does not come with replacement shocks and you will need it for RTD equipped reinstallation.
- Photo Credit Ablestock.com/AbleStock.com/Getty Images
How to Replace the Shocks and Struts in a GMC Sierra
Your GMC Sierra is not only great for hauling all kinds of loads but also for carting around your family. Whether you...
How to Replace Rear Shocks
If you've got bad rear shocks, chances are, you've got some back pain, too. That's because shocks are integral to good ride...
How to Replace the Headlight in a 2002 GMC Yukon Denali
The headlights in your 2002 GMC Yukon Denali are very simple to replace, requiring no tools. This should take a mere five...
How to Replace the Front Brake Pads on a GMC Yukon
The GMC Yukon shares much of its mechanical design with other trucks and SUVs built by the General Motors Corporation. This allows...
How to Replace Shocks on a GMC
On GMC trucks and SUVs, you will find four shocks, one for each wheel. The shocks mount between the body of the...
How to Troubleshoot a Mercedes Benz E320
The Mercedes Benz E320 is a four-door sedan that is part of the executive E-Class range of vehicles. The E320 has been...
When to Replace Shocks & Struts
A car's shocks and struts have a tremendous impact on its ride and handling. Replacing the shocks and struts is a routine...