How to Build a Baja Bug

Save

The Volkswagen Bug is a popular starting point for a capable off-road version, which is commonly referred to as a Baja Bug. The Bug has a rear-engine layout that lends itself well to being used off-road. Converting a Bug to a Baja version can be done in a weekend with the right preparation and tools. Every Baja bug is different and is built to the owner's desires, so use your imagination when envisioning the end result.

Things You'll Need

  • Jack stands (x4)
  • Floor jack
  • Socket set and ratchet
  • Sprint bars
  • New bumper for front
  • Larger wheels and tires for a VW Bug
  • Sawzall or similar cutting instrument
  • Large hammer
  • Chisel
  • Masking tape
  • Safety glasses
  • Loosen the wheels' lug nuts. Raise the Bug with a floor jack and lower it onto jack stands at all four corners. Finish removing the wheels.

  • Remove the rear engine cover and the rear bumper. To remove the engine cover, remove the bolts that hold the hinges for the cover to the body. The bumper is held on with brackets that bolt to the chassis and are removed with a socket.

  • Remove the bolts that hold the rear fenders to the body. Remove the bolts that hold the side running boards on. Remove the fender beading between the fenders and the body and set it aside for later use.

  • Remove the wires that go to the taillights and undo the throttle cable that goes to the carburetors. Unbolt the engine tin that surrounds the engine in the engine bay. These trim pieces are bolted on.

  • Cut the rear apron (rear bodywork below the engine bay) off with a Sawzall or angle grinder. Leave about six inches between the engine bay opening and the cut line.

  • Remove the engine from the engine bay. The motor is bolted to the gearbox and is also held in with a cross-member at the rear of the engine bay.

  • Bolt the fenders back onto the body temporarily. Use masking tape to mark off the shape that you want the fenders to be after they are cut. You may want to consult photos of other Baja Bugs to get an idea of what you want. Remove the fender. Use a jig saw to cut the fenders to the shape that you marked. Leave enough bolt holes so that you can bolt the fenders back to the body.

  • Use a chisel and a hammer to remove the welds for the channel that holds the engine to the body gasket, which is on the inside of the engine bay. Cut the material off from the channel downward with the Sawzall. Use a grinder to clean up the cuts and then paint the inside of the engine bay with spray paint. Apply the paint about 10 inches from the surface in smooth back-and-forth motions.

  • Reinstall the engine. Find a new place to install the taillights, since the backs of the fenders have been trimmed off. On Baja Bugs the taillights are usually mounted on the top edge of the engine bay opening. Rewire the taillights, and reconnect the throttle cable to the carburetors.

  • Tape off the shape that you want the front fenders to look like with masking tape. Use the jig saw to cut out the shape. Do not cut too close to the headlights.

  • Put the wheels back on the car and lower it the ground. Most Baja Bugs use larger wheels and tires, so this is a good time to install those as well. After that, you can install whatever accessories you want, such as sprint bars, bumpers and driving lights.

Related Searches

References

  • Baja Bugs and Buggies; Jeff Hibbard; 1983
Promoted By Zergnet

Comments

You May Also Like

  • How to Build a Rail Buggy for the Baja 1000

    Possibly the most prestigious off-road event in North America, the annual Baja 1000 desert race features motorcycles, open-wheel rail buggies, pickup trucks...

  • How to Chop a VW Bug

    Chopping a VW Bug is an art in itself. Many enthusiasts love their Love Bug so much, they want to give it...

  • How to Build a Baja Race Car

    Of all the off-road racing variants, the Baja Race Car, also referred to as the "Baja Bug," is one of the most...

  • How to Build a VW Drag Car

    The engine-roaring, tire-burning power of a drag car is not beyond the reach of a Volkswagen Beetle. There are wide range aftermarket...

  • How to Make a Baja Minibike Go Faster

    The Baja Warrior Mini Bike features a four-stroke 196 cc, 6.5 horsepower engine, telescopic front suspension, rear drum brake, front headlight and...

  • How to Repair a Frozen Engine in a Volkswagen Bug

    If the Volkswagen Bug has been sitting for several years, the engine might be frozen up. The oil seeps down into the...

  • How to Baja a VW Bug

    Turning a Volkswagen Beetle into a dune buggy is one of the oldest hot-rod projects still widely engaged in today. It is...

  • 1970 VW Bug Specs

    Immortalized in the 'Love Bug' films, the VW Beetle, also known by the affectionate nickname of 'Bug,' has been on the road...

Related Searches

Check It Out

How To Travel For Free With Reward Points

M
Is DIY in your DNA? Become part of our maker community.
Submit Your Work!