How to Adjust Shimano Bicycle Gears

Save

When the shifting performance of your bicycle gears becomes less reliable, a loose gear cable is often to blame. Each set of Shimano bicycle gears features a cable-actuated derailleur. The derailleur "derails" the chain from one selected gear to another, but only if its cable is adjusted properly. Lack of cable tension (which happens over time because of common cable stretching) causes the derailleur to respond sluggishly. If overly loose, the cable will not allow the derailleur to fully shift the chain to the next gear.

Things You'll Need

  • 5mm Allen wrench
  • Needle-nose pliers

Rear Gears

  • Shift the front gear to the outer chain ring and the back gear to the outer rear cog. This combination will place the chain farthest from the inside of the bicycle.

  • Use a 5mm Allen wrench to loosen the gear cable bolt on the bottom of the rear derailleur. If you're unsure where to find this bolt, simply follow the cable from the shifter to its terminus at the other end.

  • Turn the barrel adjuster at the back end of the rear derailleur all the way into the body of the derailleur. Then, give it two turns in the opposite direction. As the name implies, the barrel adjuster is barrel-shaped.

  • Use needle-nose pliers to pull the end of the shift cable taught, and re-tighten the gear cable bolt over the gear cable.

  • Shift to the next rear gear. If the shift is sluggish, give the barrel adjuster a quarter-turn in toward the bike, and check the adjustment once again. Continue this adjustment until the chain responds fully to the shift.

  • Shift the rear gear so that chain is positioned in the center of the cluster of gears (known as the "cassette"). Observing the back of the derailleur, you should find that the derailleur is positioned directly beneath the chain. Turning the barrel adjuster counterclockwise on the derailleur will move the derailleur in toward the bike. Adjust it as necessary.

Front Gears

  • Shift the front gear to the smallest chain ring and back gear to the innermost rear cog. The chain will now be at its closest point to the inside of the bike.

  • Loosen the gear cable bolt on the front derailleur. Once again, if unsure of the bolt's location, follow the cable from the shifter to its terminus. In this instance, the derailleur is located over the front chain rings.

  • Turn the barrel adjuster along the cable all the way in toward the bike. Depending on which Shimano design gear shifters you have, the barrel adjuster will be located either midway along the cable on the side of the bike or where the cable enters the body of the shifter.

  • Give the barrel adjuster two turns in the opposite direction (after you've turned it all the way in). Grab the end of the cable with your needle-nose pliers, and pull the cable taught. Retighten the gear cable bolt over the cable.

  • Shift to the next largest front gear. This should move the chain from the small chain ring to a larger chain ring. If the chain responds sluggishly, add more tension to the gear cable, by turning the barrel adjuster counterclockwise. Check your adjustment each time. The adjustment is correct once the chain can shift back and forth easily between the chain rings.

References

  • Photo Credit chaîne et plateau image by rachid amrous-spleen from Fotolia.com
Promoted By Zergnet

Comments

You May Also Like

  • How to Adjust Gears on a Mountain Bike

    Adjusting the gears on your mountain bike is a relatively easy exercise that can not only make your rides more enjoyable, but...

  • How to Adjust a Shimano Derailleur

    A geared bicycle will typically feature two derailleurs -- front and back. Each derailleur is responsible for shifting the drive chain from...

  • How to Use Shimano Gears

    The gears on your bicycle allow you to adjust how easily it is to pedal. If you encounter a hill, big or...

  • How to Adjust a Shimano Altus

    Shimano's Altus rear derailleur is an entry-level derailleur for mountain bikes. The derailleur is known for its low price, easy adjustability, reliability...

  • How to Adjust a Shimano Acera

    You will need to know how to adjust your Shimano Acera gears whether you are climbing mountains or commuting to work. If...

  • How to Adjust Shimano Deore Gears

    There are two ways to calibrate Shimano Deore gears: the high and low limiter screws can be adjusted to restrict derailleur travel...

  • Types of Shimano Gears

    Shimano gears are differentiated by cost and performance and are standard equipment on all kinds of bikes. Mountain bike gear types include...

Related Searches

Check It Out

10 Delicious Game Day Eats That Rival the Game

M
Is DIY in your DNA? Become part of our maker community.
Submit Your Work!