Sometimes, it becomes necessary to add another HVAC duct run in the house. This is especially common if you remodel part of your basement by adding a room. You need to heat and cool this room, and the most economical solution is to add a duct run from your existing HVAC unit. In some instances, it may become more complicated than just adding a duct run to an existing HVAC system, especially if the HVAC system isn't big enough to serve the new space. If all you are adding is a room comparable to a standard-size bedroom, though, it is easy to add a room to an existing HVAC system.
Things You'll Need
- Tape measure
- Sheet metal duct
- Sheet metal elbows
- Sheet metal collar
- Register boot
- Utility knife
- Drywall saw
- Wood screws
- Cordless drill
- Pipe crimper
- Sheet metal screws
- Wood blocking
Measure the square footage of the room. This is done by multiplying its length and width.
Calculate what size duct you'll need by using the following parameters: up to 125 square feet, use 6-inch diameter duct, 126 to 250 square feet, use 8-inch diameter duct, and if above 250 square feet, you'll need to possibly upgrade your HVAC system before proceeding.
Measure the distance from the HVAC duct by the HVAC unit to where you want the supply air register to be. Purchase the required duct and elbows from your local home improvement store. Don't forget to purchase a register boot and a register to allow the air to flow into the room.
Figure out what ceiling configuration your new room has (drywall or suspended drop ceiling). For a drywall ceiling, move to step 5. For a drop ceiling, cut a square hole in the ceiling tile where you want your register and slide the register boot into the hole. Secure the register to the register boot with screws, and this will lock the ceiling tile into place. You can then put the ceiling tile into the ceiling grid and run your duct work.
Install the register boot before you drywall. Anchor it to the ceiling joists. The square portion of the register boot will be flush with the top of the drywall. You then drywall, cut the hole, and install the register into the bottom after the ceiling is painted.
Run the duct work from the register boot back to the main duct trunk. Connect it by sliding the crimped end into the non-crimped end approximately 1 1/2 inches. Secure each joint with at least four sheet metal screws. Cut the duct as necessary to allow for needed short pieces. Make sure you crimp one end of the cut duct with your pipe crimper so that it can be connected into the duct system.
Connect the new HVAC duct run to the main HVAC duct trunk with a sheet metal collar. This collar is connected to the main duct trunk by cutting a hole that is the diameter of the collar. The tabbed portion of the collar is then pushed into the duct and the tabs are folded over inside. This locks the collar into place. The other end of the collar is slid into the duct and screwed like the previous connections.
Support the duct at least every 5 feet by using wood blocking under the duct in the ceiling joist space. The wood blocking will be cut the width of the ceiling joist, slid up in, and nailed into place. The duct work will rest on top of this wood blocking.
Tips & Warnings
- Wear gloves and safety glasses when working with sheet metal duct work. It is extremely sharp and can cause severe cuts.
- This Old House: Ventilation
- Timothy Gonyo; Sheet Metal Workers Local #18; Milwaukee, WI
- Photo Credit Jupiterimages/Comstock/Getty Images
How to Add an Air Conditioning Vent
Do you need to add an air conditioning vent to cool a hot room? This is a project that is not very...
How to Install Forced Air Ducting Into an Existing Line
Forced air ducting allows the warm air from your furnace to be distributed throughout your home. Sometimes you may need to run...
How to Add Central AC in Old Homes
Older homes have a lot of wonderful features, but one thing they don’t have is central air conditioning. That becomes important in...
How to Add Heat Vents
Sometimes you can't get the temperature in a room to a comfortable level. If you've adjusted the heat vents and still can't...
How to Add a Home Heating Duct
Home additions usually create the need for a new heating duct or two. Adding a new duct to an existing heating system...
How to Install HVAC Supply Ducts in the Basement
HVAC supply ducts transport warmed or cooled air from the furnace to each supply air register in the home. For whatever reason,...
How to Run Ductwork
Running duct work and all other heating and air conditioning-related jobs are regulated by the local building codes and the HVAC industry....
How to Transition From Round to Square Duct Work
Updating or expanding a building's forced-air heating, ventilation and air-conditioning (HVAC) system requires changes in the ducts that carry the air from...
How to Add an HVAC Return
Adding additional cold air returns to your home's air conditioning and heating duct work system can be an important step to making...