How to Install a Jack Post


Jack posts are designed to provide adjustable leveling of floors and beams, both in new and re-modeling situations. Some are one piece while others are designed for either crawl spaces or full basements. Both styles provide top and bottom plates with one end equipped with a long adjustable screw bolt. You can expect to pay approximately 50 dollars, and they are readily available at most larger home improvement stores. In re-modeling situations, they are terrific for eliminating unwanted sags in older floors.

Things You'll Need

  • 4-foot level
  • Safety glasses
  • Hammer
  • String line
  • 1/2 inch electric drill
  • 1 - 1/4 inch steel bit
  • 1 - 5/8 inch steel bit
  • 4 - 1/2 carriage bolts 2 inches long (or lag bolts--see step nine)
  • 4 - 1/2 inch washers
  • Adjustable wrench
  • If step 10 is needed -
  • 1 - 1/4 inch masonry bit
  • 1 - 1/2 inch masonry bit
  • 4 - 1/2 inch sleeve anchors - 2 inches long -
  • Follow the manufacturer's assembly instructions for your desired length. In the case of one-piece posts, make sure that your post is short enough to allow for the adjustment screw to extend. Two-piece posts will have through bolts provided to adjust for either a crawl space or full basement. In addition, make sure that you have selected a position below your work area that has either a substantial concrete floor or concrete footing.

  • Stand the post vertically below your work area to be jacked. It is always best to distribute the jacking force over a broad area rather than a single spot. This is accomplished by placing the jack under either an existing beam or providing a beam long enough to service the area. In some cases you may need a post at both ends for occurrences in the middle of a room where no beam exists.

  • Place the top steel plate provided with the jack on top of the screw bolt and begin to crank the screw with the crank rod, also provided. At this point you only want to snug the fit. Do not begin lifting at this time.

  • Place the 4-foot level against the post in the same direction of the post. Observe both the top and bottom windows. If you have never used a level before, you will need to tap the bottom of the post with the hammer in such a direction that lets the bubble move to the middle of both windows. Make sure that the top of the post remains under the beam and does not wander.

  • Move the level 90 degrees away from your initial placement and repeat the tapping process in step 4.

  • Move the level back to the first location and again tap the bottom of the post. You will note that the windows that were in line are no longer aligned. You will need to reposition the level several times between the first and second locations, tapping the bottom each time. Repeat this until the bubble remains in the center as you move the level back and forth. The post is now straight...this is essential for safety.

  • Begin cranking slowly. If you are under a long steel beam, you will need to either sight the sag as you lift by going to both ends and actually observe the lifting action. If you have a helper, he or she can actually watch and direct you in the cranking action till the beam is level. If you are alone, you will have to check several times yourself. This is made easier by placing the string line tight along the beam's length enabling you to observe the jacking yourself as you crank.

  • When you believe that the beam or sag is now level, place the level horizontally under the beam and observe the center window. If it is directly in the middle of the two lines, you will confirm that the jacking is complete. Better still, you should go to both ends of the beam and look along the bottom of the beam. If you still see a need to crank till it is straight. Four-foot levels only read accurately at that spot, so you need to confirm that the entire length of the beam is straight. You can also satisfy yourself that a sagging floor in a remodeling situation is corrected satisfactorily by actually walking on that floor, looking at it from different locations and placing the level on that surface itself.

  • You may choose at this point to attach the top plate of the post to the beam. If your beam is steel, wearing your safety glasses and using the drill and 1/4-inch bit, drill pilot holes through the top plate holes into the beam. Then change to the 5/8-inch bit and widen each hole to receive the 2-inch carriage bolts and washers. Tighten with the adjustable wrench. This will ensure that the post is not nudged out of line accidentally. If your beam is wood, use the lag bolts.

  • If the bottom plate of the post is resting on a finished concrete floor, repeat steps 8 and 9. Most bottom plates do not have holes pre-drilled. Therefore you may need to drill through the steel plate using the metal bits and then change to a masonry bit in order to drill into the concrete for the sleeve anchors. Insert the sleeve anchors and tighten. If your post is resting on a footing that will later be covered with concrete, no further actions are needed.

Related Searches


Promoted By Zergnet



You May Also Like

  • How to Install a Basement Support Post

    A basement post is usually installed to counteract a sagging frame in a wood-frame house. Typically the posts are eight-foot adjustable devices...

  • How to Install Pump Jacks

    Remodeling the outside of your home can be a challenge. Reaching the heights of the gable ends can be much easier if...

  • How to Use a Floor Jack in the Basement

    Faulty construction, the age of the building or sinking concrete footings can cause a home's floor to sag over time. Using adjustable...

  • How to Use a Farm Jack

    A farm jack is a versatile piece of equipment popular with farmers and off-road enthusiasts. A farm jack, also known as a...

  • How to Remove Metal Fence Posts

    Removing a wire fence, or moving its location, takes several stages. First the wire is unclipped, taken down, and rolled. This leaves...

  • How to Pull a Post With a Farm Jack

    Farm jacks, also known as handyman jacks, are a useful tool both and off the farm. Farm jacks are very long compared...

  • How to Jack and Block a Sagging Floor

    Sagging floors are a common ailment in older homes. In some cases, foundations have settled. In others, old framing timber has given...

  • How to Finish Basement Jack Posts

    Many basements include jack posts as part of the framing. Because they are metal, you must know how to frame around them...

  • How to Repair Concrete Footing in a Deck

    Building a deck can require a large monetary investment. A properly constructed deck should provide years, if not decades, of useful service....

  • Repair Options for Floor Joists

    Floor joists may become the victims of a number of misfortunes that require them to be repaired. Most commonly, floor joists are...

Related Searches

Check It Out

22 DIY Ways to Update Your Home on a Small Budget

Is DIY in your DNA? Become part of our maker community.
Submit Your Work!