A boat is a major investment for most people. To get the most out of your investment, and to keep repair costs down, service of the Mercruiser outdrive can be performed by the experienced do-it-yourselfer. Be sure to have a repair manual unique to your boat model and year. Servicing can be broken down into annual service, and service to be performed every two to three years.
Things You'll Need
- Socket set and socket wrench
- Drive gear lube
- Prop shaft grease
- Allen set
- Replacement parts if needed
- Repair manual (recommended)
Grease the propeller shaft by first removing the prop nut and associated hardware. Pull the prop straight off. Remove the thrust hub and liberally grease the prop shaft. Inspect the prop for damage. Get the prop rebuilt if needed.
Replace the gear lube by removing the filler plug near the bottom of the drive and the vent plug near the top. Allow gear lube to completely drain. Inspect the gear lube for moisture or metal filings. These are signs of damage to the unit. Fill the drive with new lube by pumping it into the bottom hole. When full, replace both plugs.
Clean the outer surface of the drive and touch up any nicks in the paint. Use Mercruiser paint and primer for this task.
Service Every Two to Three Years
Remove the out drive by first disconnecting the tilt cylinders and then remove the six nuts that secure the drive to the bell housing. Pull the drive straight back.
Inspect the U-joints and gimbal bearing. They need to be replaced if noise or stiffness are noticed. Inspect the bellows. If they are stiff or damaged, or if moisture is present inside, they need to be replaced.
Check the engine alignment by inserting the alignment tool. If it does not fit easily into place, the engine needs to be realigned.
Replace the impeller in the raw water pump. This is done by separating the lower unit from the outdrive and removing the water pump cover. Pry the old impeller out with a screwdriver and replace with a new one.
Tips & Warnings
- Exercise caution when removing the drive. It is heavy. During reassembly, always use new gaskets and approved gasket sealer.
Alpha One Outdrive Problems
MerCruiser, maker of the Alpha One, strongly recommends using a mechanic for serious Alpha One problems. The special fuel-delivery system and electronic...
How to Remove a Mercruiser Alpha One Outdrive
The Mercruiser Alpha 1 stern drive is a combination inboard and outboard drive. The engine is located inboard, and delivers power through...
How to Unhook the Shift Cable on a Mercruiser Outdrive
Changing the shift cable on a Mercruiser outdrive is simple if you follow a straightforward and methodical approach. Working on one of...
How to Check the Outdrive Oil on a Mercruiser
Mercruiser outdrives combine inboard engine mounting with the vectored thrust maneuverability of an outboard motor. Steering, thrust and underway boat trim are...
How to Identify My Bravo Outdrive
Mercury Marine has produced the "Bravo" sterndrive since 1986. Bravo sterndrives are capable of handling motors with up to 400 horsepower, or...
How to Repair a Mercruiser Alpha One Water Pump
The water pump in your Mercruiser Alpha One outdrive should be replaced every season to ensure trouble-free boating. The water pump circulates...
How to Align a MerCruiser Outdrive
The motor in a MerCruiser-powered boat is bolted firmly to the floor and transom inside the boat. The outdrive is bolted firmly...
How to Troubleshoot an Outdrive
Outdrives, commonly called stern drives, consist of an upper and lower unit on boats. In appearance, they resemble the lower half of...
How to Raise a Mercruiser Outdrive Manually
Although it does not happen very often, a Mercruiser outdrive can be unresponsive when you attempt to raise or lower it. Whatever...
Mercruiser Outdrive Identification
Mercury produced the Alpha One, Bravo One, Bravo Two, and Bravo Three outdrives beginning in 1972. Later known as the Generation I...
Mercruiser Alpha 1 Maintenance
Mercruiser’s Alpha One outdrives have been around for over 25 years and have a proven history of being reliable when they are...