An option when installing hardwood floors over concrete involves the installation of screed over the concrete. Screeds, otherwise known as sleepers, are pressure-treated 1x4 or 2x4 boards that can be purchased in various lengths from a home improvement retailer. The pressure treatment prevents moisture and insects from destroying the wood, making for a sturdy floor base. There are several methods of fastening the screed to the concrete slab, but screws capable of penetrating concrete are the best option because they are hardier than nails.
Things You'll Need
- Waterproof mastic
- Paint roller with extension pole
- Pressure-treated 1x4 screed
- Screw gun
- Wood screws, 1 1/2 inches long
- Concrete screws, 1 1/2 inches long
- Polyethylene film
- Circular saw equipped with wood-type blade
Roll waterproof mastic onto the concrete slab, using a paint roller. Use an extension pole attached to the roller to cover larger areas when applying mastic.
Snap lines across the floor, using a chalk box, to represent the placement of the 1x4 screeds. The snapped lines, along with the screed, will run perpendicular to the finished floor material. The first snapped line is one inch away from the wall. This small gap between the installed screed and wall will prevent the buildup of moisture that could cause discoloration to walls over a period of time. Place the following snapped lines every 16 inches until the opposite wall is reached. Once the opposite wall is reached, leave another one inch gap between the wall and screed line.
Place the screed next to the snapped lines and screw them into place using a screw gun equipped with concrete screws. The concrete screws should be a minimum of one and a half inches long. Use your feet to firmly press the screed against the slab as the screw penetrates into the concrete, to ensure that the screed will not be pushed up, which would result in uneven floors.
Cut the screed to the appropriate length when necessary, using a circular saw equipped with a wood-cutting blade. Leave a 1/8-inch gap between all joints to allow for wood expansion due to moisture and temperature fluctuations.
Place a vapor barrier over the installed 1x4 screeds. Polyethylene film, which comes in rolls, is the most widely used vapor barrier. In order to properly control vapors, the vapor barrier's seams should have a four to six inch overlap. Keep a minimum of four to six inches of extra vapor barrier around the entire perimeter of the floor to be placed behind installed wall base trim.
Overlap the installed screed with another layer of 1x4 screeds. Fasten them into place using wood screws and a screw gun. Place the screws 10 to 12 inches apart, sandwiching the vapor barrier between the screed layers. Finally, install the finish floor, such as hardwood or tile.
Tips & Warnings
- Some people prefer to use solid 2x4 pressure-treated wood instead of two 1x4 screeds. This requires the mastic application, followed by polyethylene film and then the fastening of 2x4 screeds. You will also need to use longer concrete screws or a hammer drill to pre-drill holes in the concrete slab for concrete anchors.
- Photo Credit Image courtesy of www.morguefile.com
How to Pour, Screed and Float Concrete
A brand new patio or driveway will increase the beauty and value of your home. If you've decided to pour the concrete...
How to Use a Concrete Screed
A concrete screed is a long board, often cut from dimensional lumber, which is used by two or more workers to level...
How to Screed a Base for Patio Stone
Before you can lay your patio stone, you'll want to make sure your base layers of gravel and sand are as flat...
How to Install a Screen Spline
A screen spline is a piece of rubber that pushes screening into a channel in a frame to hold the screen in...
How to Mix Floor Screed
Floor screed is a mortar-like substance that installers spread in a thin layer onto the surface of a subfloor. After the screed...
How to Screed a Concrete Floor
Screeding is where you level the entire surface of a newly poured slab of concrete using nothing more than a level wooden...
How to Screed Before Laying Pavers or Patio Blocks
When installing a paved patio, the area is first excavated to a depth of 12 inches. A retaining wall is built following...