How to Troubleshoot Table Electric Fans

Save

Electric table fans are simple home appliances that use a motor to drive fan blades for circulating the air. Inside the plastic or metal housing is an electric motor connected to a fan propeller, wiring and a rheostat-type switch for turning the motor on and off, and adjusting the speed. Read on to troubleshoot a tabletop electric fan.

Things You'll Need

  • Screwdriver
  • Wire strippers
  • Paper towels
  • Glass or countertop cleaning solution
  • Pliers
  • Spray lubricant such as WD-40
  • Superglue
  • Dry paintbrush
  • Disconnect the electric fan from the wall outlet.

  • Remove the safety cover from the front of the fan by unscrewing the cover and removing the 4 to 6 Phillips head screws or by pulling open the metal clips that hold the front cover to the back. Metal clips swing upward from the edge of the safety cover.

  • Clean the front and back of the fan blades with paper towels dampened with window or countertop cleaner such as Windex or 409 to restore proper speed to the electric fan. Be sure to remove dust and dirt from the back of the blades and along the motor shaft, as this accounts for most problems with poor performance, including slow fan blades.

  • Troubleshoot a sluggish driveshaft by applying a few drops of WD-40 lubricant to the shaft and rotating the fan blades by hand.

  • Remove the motor housing from the back of the fan by extracting the screws that hold it in place.

  • Inspect the back of the motor to be sure the two electrical wires are secured firmly to the contacts on the motor.

  • Use a dry paint brush to remove accumulated dust and dirt from the motor, then add additional WD-40 to the drive shaft where it attaches to the front of the motor. The drive shaft should spin freely when turned by your fingers.

  • Check the oscillating pull knob (it makes the fan turn from side to side) on some models to make sure the knob engages and disengages the motor when it is pulled. Adjust the knob if necessary so the hook attaches to a clip on the motor. If the knob is broken, it may be possible to repair it with glue, although your best bet will probably be to live without the oscillating feature or replace the fan.

  • Reattach or tighten broken or loose motor wires by stripping 1/2-inch of insulation from the ends of the wires, then twisting the wire strands and wrapping them to the contacts.

  • Tighten the contact screws with the screwdriver and replace the motor housing.

  • Turn the fan upside down and remove the cover from the bottom of the base by extracting the four screws holding it in place.

  • Check the two wires that should be connected to the bottom of the fan switch and reattach if loose or broken.

  • Clean the metal switch contacts by scraping the surface with the tip of the screwdriver to remove any corrosion and create a better electrical connection.

  • Reassemble the base and attach the screws.

References

Promoted By Zergnet

Comments

You May Also Like

  • Car Fan Problems

    When your engine is running, it generates a great deal of heat is by burning fuel. The cooling system is designed to...

  • How to Fix a Wobbly Table

    After one too many spilled drinks, you may decide to do something about the wobbly table you're using -- and in most...

  • How to Troubleshoot a Sunfire Radiator Fan

    Due to the transverse layout of its engine, the Pontiac Sunfire uses an electric radiator to pass additional cooling air through the...

  • How to Fix an Oscillating Fan

    Oscillating fans are now also available with remote controls making them even more convenient. There are those moments when they don't move...

  • How to Fix a Fan

    A broken cooling fan can cause your engine to overheat and even cause damage to the water pump. Learn how to troubleshoot...

  • How to Fix an Attic Fan

    Whole house or attic fans are a wonderful thing to have and often replace air conditioning units for people in climates where...

  • How to Wire a 3 Speed Fan Switch

    Ceiling fans come in all shapes, sizes and designs; they are a convenient and attractive addition to a home. Most of the...

  • How to Troubleshoot a Cooling Fan

    A cooling fan ensures that your engine is working at the proper operating temperature and helps ensure that your car does not...

  • How to Wire an Electric Fan Motor

    Electric fans are used in a wide range of applications in today's society. Some fans are used for ventilation and personal comfort....

  • How to Repair a Fan Light

    Repairing a fan light involves finding out what exactly is causing the problem at hand. Learn how to repair a fan light...

  • General Electric Refrigerator Troubleshooting

    Most refrigerators need to be repaired at some point, and General Electric refrigerators are no exception. General Electric refrigerator troubleshooting requires limited...

  • Desk Fan Repair Tutorial

    Virtually every type of desk fan is made the same way. A small electric motor with a protruding axle has a fan...

Related Searches

Check It Out

22 DIY Ways to Update Your Home on a Small Budget

M
Is DIY in your DNA? Become part of our maker community.
Submit Your Work!