How to Fix a Collapsed Roof

Save

When a roof collapses, it often is because there was not enough support underneath it, either from rot or failure to build correctly. When the weight above the roof becomes too much, the structure will collapse. If the collapse doesn't involve the entire roof, then you may be able to repair it.

Things You'll Need

  • Tarp
  • Bungee cords or rope
  • 2-by-4, 2-by-6, 2-by-8 lumber for repairs
  • Plywood
  • Felt paper
  • Shingles
  • 8 penny nails
  • Felt nails
  • Roofing nails

Cover the Roof

  • To minimize the damage, cover the collapsed area with a tarp. Determine how much you need by allowing for five to 10 feet of coverage past the damage. Tie the tarp down with bungee cords or rope, usually at the roof overhangs, just beyond the damage, until repair begins. Keep the tarp handy while working in case of unexpected rain.

  • Rip off any loose materials that were left behind and hanging. Cut through and remove partially attached 2-by-6 and 2-by-8 rafters. Once the collapsed area is free and clear of all loose and damaged debris, you can begin reconstruction.

  • Replace or repair any broken rafter. Usually, you can add a patch onto any broken rafters using a 2-by-4 of appropriate size depending on rafter sizes. Have a helper apply pressure against the broken rafter while you place the 4-foot patch against the broken rafter and insert screws to secure it into place. It may be necessary to apply a double patch, one on both sides of the broken rafter.

  • Replace roof decking with 4-by-8-by-1/2 Oriented Strand Board, or OSB, sheathing or desired exterior plywood. To determine the amount you need, multiply the length by the width of the area to be covered and divide that by 32. Use 8 penny nails to secure to roof framing.

  • Cover the exposed area of wood with 15-pound felt paper and secure with orange-cap felt nails. Reshingle the area. Determine the amount of shingles you need by multiplying the area's length by its width. One bundle of shingles equals 33 square feet. Make sure the shingles overlap correctly and follow the installation instructions on the cover.

Tips & Warnings

  • Use a helper for deconstruction or lifting
  • Always be careful when using cutting tools. When on the roof, watch for and avoid power lines

Related Searches

  • Photo Credit NOAA, ourlittlefixerupper.com, cjnorthwestconstruction, dtag building technologies
Promoted By Zergnet

Comments

Resources

You May Also Like

  • How to Fix Broken Glass in a Window

    That ill-flung baseball or confused bird always seems to find your window. If it broke a single-pane window, you're in luck--this is...

  • How to Repair a House Rafter

    A house roof bears an incredible amount of weight: tons of rafter and sheathing wood (or roof decking), tar paper, flashing and...

  • Patio Roof Repair

    A leaky roof can cause more damage than the homeowner really knows. Once it starts leaking it affects every area around it....

  • How to Fix a House Roof That Is Sagging in the Center

    There are a few different problem situations that may account for a sagging rooftop. The most common cause is a broken rafter....

  • How to Fix a Sagging Rafter

    Sagging rafters are caused by the wood splitting or cracking in your attic. Repair rafters with faults as soon as you notice...

  • How to Fix Broken Glass in a Window

    Fixing broken glass in a window requires a window cut to just the right size, which should fit easily into the frame...

  • Structural Roofing Repair

    Structural repairs are essential for a roof to continue supporting its weight. Usually you need to make the repairs because of the...

Related Searches

Check It Out

22 DIY Ways to Update Your Home on a Small Budget

M
Is DIY in your DNA? Become part of our maker community.
Submit Your Work!