Return air ducts inside your home increase the energy efficiency of your heating and cooling units. Much like a pump, air is heated or cooled by your furnace or air conditioner and circulated throughout the home. However, the system needs an intake of air to supply the process. Properly sized and placed air ducts fill this need. The ducts allow the air conditioner or furnace to suck air in from various rooms. Each duct opening is covered with a return air grille. Mounted to either the ceiling or the duct housing, the grille has wide openings through which the air flows.
Things You'll Need
- Utility knife
- Tape measure
Access the area holding the return air duct. Work from the attic if possible, or from the room if the top side of the air duct is not accessible.
Unscrew the old return air grille, if present, to remove the screws holding the air grille in place. The screws penetrate either the drywall -- sometimes called sheetrock -- covering the joists where the air duct ends, or the air duct housing, in which case the grille sets down flush with the drywall and connected to the duct itself.
Enlarge or create a new opening, if necessary, first measuring and marking the opening to correspond with the size of hole needed. Slice through the sheetrock with a utility knife to carefully create the opening. Replacing one style of grille for another, for example, may require a larger hole.
Measure the opening again to verify the size. The height and width of the opening must meet the specifications provided with the particular air return grille you use. Shave additional adjustments away until adequate.
Place the return air grille against the ceiling, over the appropriate hole. Drive screws through the holes provided in the air grille cover into the duct housing, if present, or into the joists surrounding the hole. Tighten the screws firmly, but do not over-tighten to avoid digging your frame into the drywall, damaging it.
Tips & Warnings
- An air return duct by definition must use either the space between the joists or a distinct duct to transfer air. Therefore, the air return opening should have wood completely framing the opening, under the drywall. If you find a lack of wood to attach the grille to, cut 2-by-4 inch boards to fit the space involved and nail between the ceiling joists to secure. If done from the upper side, you don't even have to disturb the sheetrock; if you have to do so from the bottom, you will have to cut a much larger opening. Mark the dimensions for the new grille on the replacement sheetrock before securing in place. Attach the grille to the sheetrock, piercing the wood behind, as normal to install.
- Photo Credit Jupiterimages/Photos.com/Getty Images
What Is a Ceiling Diffuser?
Ceiling diffusers are one of the few visible parts of an air conditioning system. Typically mounted in the ceiling of a home...
How to Change the Ceiling Air Filters in House Vents
Homes with central air conditioning and heating units have ceiling-, wall- and floor-mounted vents that pull air into the system where it...
How to Install Air Ducts
Air ducts are hollow tubes (square, rectangular or round) that carry heated and/or cooled air throughout a building. Older buildings often do...
How to Move an Air Conditioning Flex Duct
If you have an air conditioning flex duct that needs to moved you can do it yourself. It is not hard to...
How to Install a Return Air Duct
A return air duct is what carries air back to the furnace after it is dispensed throughout the home through the supply...
How to Install Basement Ceiling Vents
When the basement isn't quite as warm or as cool as you'd like it to be, the solution is usually a few...
How to Install a Return Grille
Supply air registers supply rooms in your home with heated or cooled air from the furnace. Return air grilles return the air...
How to Size an Air Conditioner Return Air Duct
Properly sizing and installing your air conditioning system are important in making sure your air conditioner operates efficiently, according to the U.S....
How to Increase the Capacity in an Existing Return Air Duct
Air flow to an air conditioning or heating system is critical for proper operation. An air-starved unit will not only have poor...
How to Paint Air Return Grilles
Most any amateur knows the basics of painting drywall. Unfortunately, if you attempt to paint an air return grille using these techniques,...
How to Size Return Filter Grilles
The most common place you will find furnace filters are either in the unit or in the return air ductwork right next...
How to Add an HVAC Return
Adding additional cold air returns to your home's air conditioning and heating duct work system can be an important step to making...