How to Make a Tool Roll

Tool rolls are convenient ways to store and carry small tools such as wrenches, screwdrivers, chisels and files. You can customize your tool roll to suit your personal tool selection by adjusting the width of each tool slot, the number of tool slots and the length of the overall roll. Make sure you have a heavy duty sewing machine and needle that are capable of stitching through multiple layers of heavy cloth. While canvas is recommended for easier sewing and low cost, you can also make your tool roll out of leather for increased durability.

Things You'll Need

  • 18 by 24-inch heavy canvas fabric
  • 3 yards 1/2-inch wide double-fold bias tape
  • Fabric scissors
  • Pins
  • Sewing machine
  • Heavy duty thread
  • Measuring tape
  • Chalk marker
  • Straight edge
  • 24 inch long 1/2-inch thick heavy duty elastic
  • Grommet kit
  • 1/4-inch grommet

Instructions

    • 1

      Lay out a piece of 18 by 24-inch canvas so the longer sides are horizontal, and cut two pieces of 24-inch bias tape with sharp fabric scissors. Pin the bias tape to the top and bottom edges of the canvas roll, then sew the bias tape on using a straight stitch and heavy duty thread, such as bonded nylon, removing the pins as you go.

    • 2

      Measure 6 inches up from the bottom of the canvas and fold up the fabric on that mark, so the canvas is now 12 by 24 inches with a 6-inch flap at the bottom. Pin this in place.

    • 3

      Measure 3 inches down from the top of your canvas on each end. Pin one end of the elastic to each end of the canvas on these marks. Cut two 13-inch pieces of bias tape and fold the last 1/2 inch on each end inward to create a clean fold on the ends. Pin these to the short sides of your tool roll, over the folded flap, horizontal bias tape and the elastic. Sew the tape in place, removing the pins as you go.

    • 4

      Measure and mark the top and bottom edges of the roll, using a chalk marker, at the following increments (in inches): 2, 4, 6, 8, 10, 12, 13.5, 15, 16.5, 18, 19.5, 21 and 22.5. Connect the top and bottom marks by drawing a line using a straight edge, then sew along the lines, either the full height of the roll or just along the flap and the elastic. This creates your individual tool slots.

    • 5

      Mark the spot 1/2 inch in from the right edge of the tool roll, just above the folded flap. Use a grommet kit to install a 1/4-inch grommet according to the kit's instructions.

    • 6

      Fold your remaining bias tape in half and twist the folded edge together until it is small enough to fit through the grommet hole. Poke the twisted end through the grommet until approximately 1 inch is showing through, then run the free ends of the bias tape through the loop this creates by passing them over the outside edge of the tool roll, through the folded end of the tape and pulling tight. This secures the bias tape to the tool roll; when rolled up from left to right, the loose ends can be tied around the roll to secure it.

Related Searches

References

You May Also Like

  • How to Make a Leather Tool Roll

    A leather tool roll is a great way to keep tools organized and protected. You can make several of them to hold...

  • How to Make Dinner Rolls

    These dinner rolls smell as good as they taste. You'll never reheat store-bought again! Makes 18 rolls.

  • How to Make Avocado Rolls

    If you are hosting a party and some of your guests do not like seafood, you can still treat them to delicious...

  • How to Make Cinnamon Rolls

    Admittedly, cinnamon rolls are not that easy to make. But once you get the hang of it, you'll want to perfume your...

  • Roll-Up Tool Pouch Instructions

    A roll-up tool pouch can be used to hold a wide variety of tool types, including paint brushes and knives, electrician's tools,...

  • Sewing Ideas Using Fabric Jelly Rolls & Charm Packs

    Sewing Ideas Using Fabric Jelly Rolls & Charm Packs. Jelly rolls and charm packs are pre-cut bundles of coordinating quilting cotton. Jelly...

  • How to Use Landscaping Fabric

    Purchase your landscaping fabric. You can get rolls of fabric at most stores that sell plants. If you have a small project,...

  • Pro Tools Control 24: Post-Roll Tips

    Post-roll is designed to let the recording musician hear how what was recorded blends into the following section of the song. Use...

  • How to Make a Periscope With a Paper Towel Roll

    A periscope is a tool used to look over objects or to look at a higher elevation. Periscopes are well known for...

  • Pro Tools Pre-Roll Options

    The pre-roll button in the Pro Tools transport window allows the user a set number of bars or beats of the click...

  • How to Make Roll Up Canvas Shades

    The right window treatments can add a level of class and distinction to any room. A great choice to consider for the...

  • How to Make a Canvas

    Artistic painters, both recreational and professional, will benefit from being able to create their own quality canvases upon which to design their...

  • How to Make Metal Wrench Chimes

    This project sounds weird, but the tone of these chimes is quite nice. Use box-end wrenches for a pleasant-sounding ring.

  • How to Make Bonsai Pottery

    Bonsai pottery is designed to accentuate, and never overwhelm, the beauty of a bonsai tree. Trees are planted in low, shallow clay...

  • How to Repair Roll Up Blinds

    Roller up blinds consist of a hollow aluminum tube at the top. The fabric covers the metal tube, and a spring is...

  • How to Sew a Knitting Needle Roll

    An experienced knitter will tell you that keeping needles and other knitting tools organized can be a nightmare. Stay organized and productive...

Related Ads

View Blog Post

Wrap up in Style with this DIY Wool Blanket Coat