Instructions for an AM Loop Antenna

Save

You may have accepted static and poor reception on your AM radio as a fact of life. The fault may not be with your signal or even your location in relation to the transmitting tower. It could be the fault of your radio’s antenna. The ferrite coil antenna in most AM radios is a small rectangular bar that is just large enough to allow the radio to receive local stations. You can improve your reception by improving your antenna.

Loop Antennas

  • A loop antenna, as the name implies consists of a loop or number of loops made of copper wire wound on a nonconductive frame. The frame is generally made by joining two pieces of wood together to form an X shape. On a spiral loop antenna, the copper winding begins on the outside edge of the X and is wound in a spiral shape toward the center.

    An edge-wound loop antenna uses the X-shaped frame constructed from 1-by-6 inch boards. The ends of the board are notched at half-inch intervals and, as the name suggests, the copper wire is wound around the edges of the frame.

    In both cases, the two ends of the wire are connected to a variable 365-picofarad capacitor that is used to tune the antenna to the correct frequency for the radio station.

Building an Edge Wound Loop Antenna

  • Take two 18-inch 1-by-6 inch boards and place a mark on both at the mid-point on one edge. Place two more marks on both boards 3/8 inch on either side of the mid-point. This will give you a 3/4-inch measurement in the center of the boards. Use a square to mark a slot beginning at these marks running to the middle of the flat side of each board. A 1-by-6-inch piece of finished lumber actually measures three-quarters of an inch by five-and-a-half inches, so the middle of the flat side will actually be two-and-three-quarters inch. Use a small handsaw to cut the marked slots out of each board. Put the boards together by aligning the slots and pushing the outside edges of the boards until they reach the bottom of the slot. The result should be an X-shaped frame.

    Use the small handsaw to make eight, half-inch deep slots, one-half an inch apart on all four ends of the frame.

    Wrap 22-gauge copper wire around the outside of the frame through the slots. Mount the variable capacitor anywhere on the inside surface of the frame and attach both ends of the copper wire to the capacitor’s terminals.

Use

  • Tune your AM radio to a station with weak reception. Place the antenna on or next to the radio and slowly adjust the dial on the capacitor up and down. Loop antennas are directional, after the reception improves, try rotating the antenna from left to right.

References

  • Photo Credit tape measure 1 image by Martin Grice from Fotolia.com
Promoted By Zergnet

Comments

Resources

You May Also Like

  • How to Build a Flat AM Loop Antenna

    Amplitude modulation (AM) radio receivers can use a variety of antenna designs, and one that offers superior reception is the loop antenna....

  • How to Make a Radio Antenna

    You've moved to a new apartment and your radio reception is awful, but store-bought antennas are expensive. Why not build your own...

  • How to Hook Up an Antenna for an AM Receiver

    An AM radio receiver will almost always deliver better reception when connected to an AM antenna. A common type of AM antenna...

  • How to Make a Loop Antenna for an AM Radio

    AM radio reception can be a little tricky, given its highly directional nature. However, the characteristics of a well-built loop antenna and...

  • How to Make a FM Loop Antenna

    A loop antenna is a simple antenna design that has many attributes. It's compact, easy to make, and also is directional—you can...

  • How to Make a Simple AM Antenna

    The radio waves of an AM broadcast are weak compared to FM, and require an antenna for being received correctly by an...

  • DIY UHF Antenna

    UHF antennas are useful in areas without cable or satellite service but where over-the-air television reception is readily available. There was a...

Related Searches

Check It Out

Geek Vs Geek: Robot battles, hoverboard drag race, and more

M
Is DIY in your DNA? Become part of our maker community.
Submit Your Work!