Rochester carburetors were quite possibly the most widely used carburetor in the twentieth century, with over one million units produced by the Delco Carburetor Company, a division of General Motors. Rochester carburetors are known for their durability and simplistic design, yet even Rochester carburetors will eventually develop problems. Thankfully, the most challenging part of repairing the carburetor is first identifying the likely causes of the problem.
Cold No Start or Stall
If the engine will not start due to a carburetor problem when the engine is cold, the cause is most likely a defective accelerator pump. In fact, this is one of the most common problems with Rochester carburetors. The accelerator pump is particularly vulnerable to vacuum leaks, backfires through the carburetor and dirty gasoline. If the accelerator pump is in good condition, the problem may be with a choke that either will not close because it is caught on something, or because the choke linkage requires lubrication. It the engine does start when cold, but stalls after a few seconds, check whether the idle screw on the driver's side of the carburetor needs adjustment. If the idle screw is not screwed in far enough, the engine simply is not being supplied with enough gasoline to idle. Another cause which can be traced to the carburetor is a float level which is set too low.
Hot No Start or Stall
If the engine will not start when the engine is hot, the choke may be stuck in the closed position, typically due to a lack of lubrication. However, chances are good that the problem is caused by something other than the carburetor, such as a large vacuum leak, a lack of compression or a fuel supply problem, such as a kinked or clogged fuel supply hose. If the engine does start when hot, but stalls after a few seconds, again, the choke may be stuck in the closed position. If the choke is in the open position, the carburetor's power valve may have blown, or the idle jet within the carburetor may be clogged with dirt.
Hesitation or Stalling During Acceleration
If the engine either hesitates or stalls upon acceleration due to the carburetor, the carburetor's accelerator pump nozzle may need to be cleaned or the secondary throttle plates may not be closing all of the way. Occasionally, the carburetor's idle jet will become clogged with dirt, which will cause the hesitation or stall. Finally, check to ensure that the vacuum lines which connect to the carburetor are hooked up correctly.
Hesitation or Stumbling Under Heavy Acceleration
If the engine hesitates or stumbles only upon heavy acceleration, inspect the accelerator pump for the presence of dirt and replace the pump if necessary. The problem might also be caused by sticking metering rods or a defective power valve. The float level may also be too low, which prevents the carburetor from storing an adequate supply of fuel for heavy acceleration.
- Haynes Techbook: Rochester Carburetor Manual; Mike Stubblefield and John; 1999
- Rochester Carburetors; Doug Roe; 1987
How to Identify Rochester Carburetors
Rochester carburetors can be identified in a number of ways--a metal tag that can be triangular or circular, hanging from or pressed...
How to Decode Rochester Quadrajet Carburetor Numbers
How to Identify Rochester Carburetors. Rochester carburetors can be identified in a number of ways--a metal tag that can be triangular or...
How to Adjust a Rochester 2 Barrel Carburetor
Rochester 2-barrel carburetors have an adjustable float, a replaceable main metering jet, an accelerator pump and an adjustable idler metering screw for...
Rochester Carb Factory Specifications
Carburetors deliver a combination of air and fuel to internal combustion engines. These components use intake and exhaust valves to divide and...
How to Rebuild a Rochester 2BBL Carburetor
Consult the rebuild kit's specification chart for the necessary adjustments and assembly guide. 5. ... Rochester Carburetor Troubleshooting. Rochester carburetors were ...
What Makes a Car Hesitate When Accelerating?
On vehicles equipped with carburetors, engine hesitation can be directly caused by a bad or abnormally functioning carburetor. ... Rochester Carburetor Troubleshooting.
How to Adjust the Float on a Rochester Carburetor
Rochester Carburetor Troubleshooting. Rochester carburetors were quite possibly the most widely used carburetor in the twentieth century, ...
How to Tell if a Carb Jet Is Clogged
How to Tell if a Carb Jet Is Clogged. ... Rochester Quadrajet carburetors were used by General Motors on many of the...
How to Troubleshoot a 2 Barrel Carburetor
Rochester Carburetor Troubleshooting. How to Identify Rochester Carburetors. Featured. 10 Tips for Used Car Shopping. View Photos. How to Check & Add...