Cycling with children in tow can be a fun bonding experience and a great workout. Instep bicycle trailers are among the best made and most widely available.
The Sides and Seat
After removing trailer from carton, place the wheels off to the side and position the trailer so it's flat and the front is facing you. Fold the left and right sidewall up so the u-shaped bars that support the flaps are erect. The rear of the right sidewall should have the back rest for the seat already attached to the top. On the left of the seat back rest, attach the frame joiner insert--a sort of plastic tab--into the housing on the rear of the left side wall. This will allow the back rest to raise and snap into place. Adjustable straps below the seat allow it to be adjusted for firmness and loosened for storage.
Lay the canopy over the the frame with the clear door facing upward. The clear door should fold or roll backward toward the back of the trailer. From front to back, attach all corresponding snaps along the left and right sides of the canopy to the snaps along the outer trailer side walls.The special loops can be affixed around corresponding bars for extra security.
The Tow Bar and Wheels
The tow bar swivels under the trailer floor for storage. Undo the locking pin to swing the tow bar forward, and replace the locking pin to secure the bar in a forward facing position.
Hold the wheels, hubs facing out, and slide the attached wheel axles into the brackets on the side and rear of the trailer. Push the wheels in until they click and then pull the rim out firmly to ensure they are secure.
The coupler is the piece shaped like a figure-eight, with a small top and a large bottom.
For rear wheels with quick release levers, open the lever and remove the axle nut and spring from the other side of the hub. Completely remove the axle skewer. Run the skewer through the hole of the small side of the coupler, slide the skewer back through the wheel hub and then replace and tighten the spring and nut on the other side. Tighten and close the lever, and make sure it is snug.
Insert the end of the tow bar into the large portion of the figure-eight coupler and attach with provided pins. A heavy nylon safety strap on the tow bar should be looped around the outside rear lower bike frame bar for added connective security.
For axle skewers with nuts and washers instead of quick release levers, follow the same directions but use an adjustable wrench to loosen and remove the skewer. Then re-tighten at the end.
For take-down and storage of the trailer, reverse all assembly directions.
How to Connect a Schwinn Bike Trailer
Using a bike trailer is a great way to get out and about with your small children or pets. You also can...
How to Attach a Bike Trailer to a Bike
Biking is a great family activity. Young children who cannot ride yet could feel left out, but the next-best thing is to...
How to Install a Schwinn Bike Trailer
Schwinn bike trailers are light, convenient and sturdy. If you've lost the hook-up instructions, the installation process is pretty basic. It relies...
Instructions for an Instep Safari TT
Schwinn's Safari TT jogging stroller features an instant lock switch to switch the jogger to a swivel stroller with the flip of...
Instructions for Master Cycle Bicycle Trailers
Kuji Sport Company has been making the Master Cycle line of bicycle trailers since 1992. These trailers attach to your bicycle with...
Instructions for the InStep Quick N EZ Bicycle Trailer
The InStep Quick N EZ Bicycle Trailer is a perfect addition to any bicycle. It easily attaches to the rear wheel, providing...
How to Replace Parts for an Instep Quick EZ Bike Trailer
Replacement parts for an InStep Quick EZ bike trailer can be purchased through your local InStep retailer, which is often a bicycle...
Knitting Socks: Instep
When knitting socks, the instep is done using several circular needles. Knit the instep of a sock with tips from a knitting...
Schwinn Bicycle Trailer Instructions
The Schwinn bicycle trailer is a revelation in ease and enjoyment. They come in different configurations, are affordable and are easily assembled....