home sectionhome section
Shower door spline is a U-shaped rubber or plastic channel with ribs on the outside. It is also called vinyl glazing channel. This channel fits down inside the metal frame of a shower door. The spline acts to support the glass or plastic panel of the door as well as provide weatherproofing. Over time the spline breaks down and should be replaced. It is important to use the right size and shaped spline for your particular door. Remove the old spline before purchasing the new spline.
Shower doors pivot or slide on an aluminum frame that attaches to the shower walls by plastic anchors or cement fasteners. After removing the frame, unsightly holes may remain in the shower walls. The method to repair the holes depends on the type of shower walls. You can repair shower walls covered in ceramic tile or natural stone with a color-matched grout. For shower walls covered in vinyl or fiberglass panels, a color-matched caulk is recommended.
Before installing new doors or opting to simply put in a shower rod, it is necessary to remove the old sliding doors from the bathtub or shower. Sliding bath doors operate similar to a sliding patio door except that both panels are mobile. There is a small amount of hardware on a sliding bath door that requires removal to take apart the doors and frame. Removing sliding doors from bathtubs and showers requires protecting the floor of the tub or shower while you are working inside.
The surface of a shower door is not always flat. Therefore, using a straight edge to remove stubborn tape from the rough surface makes it easier to nick or scratch the door. Sometimes removing tape is as quick as pulling off the tape with your fingers and using a cleaner to break down the adhesive. If ignored, tape can stubbornly adhere to the surface and you must forcibly remove the outer tape before tackling the adhesive. There are products on the market designed specifically to break down adhesive. Yet, it is possible to complete the task with vinegar.
Clear shower doors with decoration etched into the glass require careful cleaning to maintain its spotless appearance and eliminate soap scum that accumulates due to continuous use. Although scrubbing brushes and pads are suitable for porcelain surfaces in the bathroom, these abrasive cleaning tools create tiny scratches on the glass, reduce glass transparency and can wear away the decorative etching. The key to proper shower door cleaning is with a mild glass cleaner. The shower door must be cleaned on a weekly basis to reduce soap scum buildup.
Those tiny glue humps, left from a recent shower door repair, stare at you mockingly from your bathtub surface. The bonding power of the adhesive holds steadfastly to a flat surface, requiring a powerful product to break down the glue's stronghold without etching the tub. With the right techniques you can banish those rigid lumps from your tub without breaking a sweat.
While a glass shower door is naturally resistant to mildew because it's non-porous, it can develop thick deposits of dirt, grease or soap scum that serve as food for mold spores. Thus begins a cycle of mildew growth, particularly when the shower door is covered in moisture. You can remove mildew with solutions you may already use for routine cleaning.
Silicone sealant is a common material used to waterproof the edges of most bathroom fixtures, including the areas around your shower door. The sealant doesn't last forever though, and will need to be replaced every so often. You will also need to replace the sealant if and when you remove the door itself. The sealant can be difficult to remove without the right tools, but is quite simple when you know what you're doing.
Silicone sealant is a waterproof adhesive, often found in caulk, used to seal joints in various structures, such as those around plumbing fixtures, baths and showers. Because silicone caulk on a shower door is continuously exposed to water and moist conditions, it can become damaged by mildew or mold. If so, you need to remove the silicone sealant before replacing it.
The sliding tub top doors of a bathtub may cause problems. If the doors reduce accessibility to the tub, or simply look old, it's time for a change. Leave the space above the tub open if you prefer taking baths to showers, or replace old tub-top doors with a new shower door or curtain. Whatever your plans, the first step is to remove the old sliding tub top doors.
Sticky adhesive on your tub shower door quickly attracts other dirt and debris. If a manufacturer's label has left adhesive residue, you must remove it to avoid the buildup of a bigger stain. Dirt, hair and soap scum can cause white adhesive residue to become an eyesore on your shower door. You can remove this stain with supplies that may already be in your bathroom. Use these products and the right technique to get the adhesive stain off the door without scratching the surface.
Tile showers are like many construction projects -- an overwhelming component of the quality, durability and longevity of the do-it-yourself project is determined by the appropriate installation products used. From multi-colored natural stone like slate to tiny handmade glass mosaics, the correct approach to a shower tile installation starts with selection of the correct type of thinset.
Every tile professional knows that you must immediately wipe away any thinset that gets on tile faces to prevent the much longer, tougher task of cleaning dried thinset from ceramic tiles. If you see thinset on tile after a tile installation job, it's possible to remove it. However, if you plan to reuse the tile after you remove the thinset, it's probably worth it to just buy new tile and save the effort.
Thinset mortar is a Portland cement-based mortar adhesive, most commonly used for tiling. Don't let the "thin" in its name be confused for anything like weakness, because once set, thinset is extremely difficult to remove. While some thinset may be removed by scraping or using a pneumatic chipper, most of the time a sulfamic acid application will be necessary to complete remove the thinset from concrete.
Whether you're giving your double wide trailer's bathroom a facelift or performing major plumbing repairs, you may have to remove the shower assembly. While the task may seem intimidating, removing the shower from your mobile or pre-fabricated home is similar to removing a shower from a traditionally built home or structure. It takes a good amount of planning, as well as plumbing tools and supplies that can be purchased at your local hardware store.
In order to perform routine maintenance on a leaking shower faucet or to replace a broken handle, you'll have to access the inside of the device. This project will involve removal of the decorative plastic shower handle. This plastic handle covers the metal faucet underneath, and is usually held in place with little more than a few screws.
Water usage codes require that shower heads only put out so many gallons of water per minute. Low flow water regulators have tiny holes through which water passes. Over time these holes can plug up reducing water flow to a trickle. Mineral deposits in these holes must be removed to restore proper water flow. A low flow water regulator can usually be found in between the shower arm and the shower head. The old regulator should be cleaned and replaced, or a new one can be installed.
Mobile homes have been present in America since the time of the first vehicles. Mobile homes are available in a variety of sizes and styles and are highly preferred by some homeowners due to their cost and mobility. One of the most popular styles of mobile home is the double-wide; made from two separate sections that are connected on site. If your double-wide mobile home is in need of new windows, you can replace the existing ones with the proper materials and by following a few simple directions.
A baseboard heater encasement can be removed with little effort. Designs may vary, but the removal method generally stays the same. At the end of the encasement two end caps hold the encasement in place. These end caps can be held on with screws or a snap-in mechanism. The top of the encasement has an underlying ridge that rests in an underlying groove. Reasons for the removal of a baseboard heater encasement include maintenance, cleaning and painting.
Sliding shower door frames don't last forever and when the time comes to remove it, you can do it yourself. A sliding shower door frame is composed of four main parts: the header, the two sides and the base. The sliding doors fit into the tracks of the header and the base. The only things holding the frame in place are screws and caulking. Once the doors, screws and caulk are removed, the frame can be dismantled.
Your horse trailer can be converted to a camper, and you can even equip it with conveniences. Although your space certainly is more limited than in an RV, options might include a microwave oven, an entertainment center, a refrigerator, a sink, a bed, cabinetry and even a shower and a toilet. A cowboy shower is a box, containing the showerhead and hose that can be folded and stored in the shower pan when not in use.
Hard water, rust, water deposits and everyday use can leave stains on the inside and outside of a fiberglass shower door. Using a harsh bathroom cleaning product could result in new stains or marks appearing on the fiberglass door. Lime Away Trigger is a cleaner mild enough that it won't harm the fiberglass surface, yet strong enough to remove both stains and odors have been on the door for a long period of time.
Federal regulations force shower head manufacturers to limit the water output of modern shower heads to 2.5 gallons of water per minute. The output limitation preserves water, but also produces an undesirable effect for consumers: low water pressure. To limit water flow, manufacturers place a small plastic screen in the head, called a flow restrictor. The flow restrictor partially blocks water from passing through the shower head, reducing the water output per minute. The restrictor is removable with just a few adjustments to the shower head, allowing you to take a high-pressure shower with a flow-restricted shower head.
A tub drain covered by a metal piece with drainage holes is known as a "strainer" drain. The holes are large enough to let hair and soap scum pass through, which causes the drain to empty more slowly. Removing the strainer to clean out the tub drain is a simple process, and gets the drain flowing properly.
Leaks around the tub floor can usually be attributed to a poor seal between the tub drain strainer and the bottom of the tub. Removing the tub drain strainer is necessary to apply a new seal or replace the strainer if it is damaged. The drain strainer screws into a shoe below the tub. The most difficult part of removing the drain strainer is breaking the seal completely. Although there are specialty tools available for removing the drain strainer, simple hand tools are usually all that is necessary.
So, it's time to give your doublewide trailer's bathroom a makeover. Don't be intimidated by the job, even if it is something you never have done before. Renovations on a mobile home or prefabricated home are not much different than those done on a conventional home, and the building materials required are available at any home improvement center. If you plan out the process, you will have all the right tools and materials needed to do the job.
The Delta series 1700 shower faucet uses a single handle with a temperature adjustment dial to control water pressure and temperature. The temperature adjustment dial mounts to the front of the handle. A Delta 1700 series cartridge assembly contains two inlet ports, which connect to the home's hot and cold water pipes. When the handle's temperature adjustment dial turns, the cartridge's internal valve adjusts the hot/cold water ratio. Turning the handle adjusts the water flow's volume. Removing the Delta series 1700 faucet's temperature adjustment dial and its handle allows access to the faucet's cartridge.
Etching occurs on shower doors when hard water continually runs down the shower door and leaves mineral deposits on the surface. You can remove this etching by using homemade cleaning solutions. Prevent etching by installing a water softener or by wiping down your shower doors after every shower.
If your bathroom could use an update but you can't afford a complete remodel, try swapping out old fixtures for new ones. Fixtures such as shower knobs are available at home-improvement stores, and they range in design and construction so as to suite a variety of tastes. Removing and replacing shower knobs does not require hiring a plumber or pricey repair person. Do it yourself.
Soap scum will build up on shower doors over time if you do not clean these areas often. The doors will look hazy and unattractive. It can be hard to remove soap scum from the shower doors, especially if you leave the scum sitting for a long time. Instead of using harsh chemicals, remove the scum yourself using ingredients you probably already have on hand. Once you remove the soap scum, you must clean and dry the doors often to prevent the buildup from returning.
When removing lime scale from shower doors, you'll need lime-scale remover and glass cleaner. Learn how to properly remove lime scale and keep your doors sparkling clean with the useful tips from the founder of a premier boutique cleaning service in this free video on how to remove lime scale from shower doors.
Limescale is a hard-water stain that can accumulate on shower doors, toilet bowls and sinks. Limescale attracts soap scum and mildew, making the stains even harder to remove. While you can remove limescale with a commercial, acidic cleaner, those products should be a last resort because of their toxic fumes. Regular vinegar sprayed on the shower door should remove the stains.
Etching on shower doors is caused by hard water stains. Hard water is filled with minerals such as calcium and magnesium, and because of this, it creates a slew of cleaning problems. It prevents detergents and soaps from performing properly, and when the minerals dry on your shower door, they and the soap residue from bathers leaves the shower door with a dirty, dingy "etched" look. Fortunately, you can remove this and clean your shower doors without using toxic chemicals.
Water spots on shower doors can be removed with simple, homemade solutions made from common household ingredients, such as white vinegar and baking soda. These solutions may also be helpful for removing spots from chrome fixtures, windows and mirrors.
You can have one of several materials covering the walls of your shower enclosure, including tile, stonework and fiberglass. Unless you have a shower curtain, though, your enclosure probably has a glass door. Glass lets in needed light, and it's relatively easy to keep clean. There are two types of glass shower doors: those that pivot on a hinge, and those that slide in a track. Whichever you have, removing it is a simple task that shouldn't take more than 30 minutes.
Tiling is a messy job and cleanup is important, because if grout or thinset are left on the tiles, removing it can be a pain. If you notice thinset on the tile in your shower floor after a new installation, you must wait at least a week before attempting to remove it to avoid damaging the grout work on the tiles. Old thinset should be removed as soon as you notice it; the longer it sits there, the harder it will get.
Most shower doors that swing out use pivots to open and close the door. Repairing the shower door, or replacing pivots, requires removing the door. The removal process is different among door manufacturers, but the general concept is similar. Removing the shower door requires disengaging the upper pivot from the door and frame so that you can remove the door from the lower pivot hole. Once the upper pivot is out of the way, the door removes from the opening with little difficulty.
The Delta Monitor 1400 shower faucet uses an anti-scald device that keeps you from accidentally turning the water on too hot. Periodically you may need to make adjustments to the anti-scald feature, or even replace the faucet cartridge which requires removing the faucet handle. Removing the handle on a Delta Monitor 1400 shower faucet is a matter of locating the set screw that secures the handle. The set screw is behind a decorative cover plug that blends with the handle,virtually hiding the screw.
Sliding shower doors provide a solid barrier between your shower and the bathroom beyond. One problem with sliding shower doors is breakage. Accidents happen and small children break things. If a sliding shower door is broken, the glass or plastic panel could cause severe cuts. Removing the doors and installing a shower curtain will prevent this hazard. Removing your sliding shower doors takes just a little time, a couple of tools and a bit of know how.
Shower doors that swing out from the shower stall rather than slide have snap-in door seals that prevent water from leaking around the door frame. Over time, the vinyl on the door seal can get moldy or even develop cracks, allowing water to seep onto your bathroom floor. The seals snap into channels along each side of the shower door frame. Removing a snap-on shower door seal requires unlocking the seal from the front channel first.
When an old shower insert begins looking worse for wear, removing it and replacing it with a brand new style not only improves the value of the house but also makes the bathroom look like new. Since many inserts are prefabricated, taking out an old stall and installing a new one is an easy weekend project. Taking out an old shower insert takes only a short period of time and requires only a few tools.
Keep water where it belongs and add seamless beauty to your bathroom by enclosing your shower with glass. You also can add a spa-like experience to your daily cleansing routine by installing a shower panel. Glass doors and high-tech panels are easy to install and will not only bring you years of relaxing, therapeutic showers they add an instant upgrade to your bathroom.
Removing your Price Pfister's shower control cartridge is a simple do-it-yourself job. It's a good idea to have the original cartridge with you when purchasing a new one, so you can ensure that you have the correct replacement. The shower control cartridge is responsible for turning your shower on and off and controlling water temperature. If either of these functions are not working correctly, then your control cartridge needs to be replaced.
Dirt and oils from skin and hair along with soap residue contribute to a layer of shower floor crud. The longer this is allowed to build up, the longer it takes to remove. This buildup tends to be worse in corners, and may also contribute to mildew growth. Removing the unsightly buildup from a shower floor will make the shower area look much more sanitary, and make showering much more pleasant.
Leaking shower floors are a common issue in older homes that were built before modern water-proofing shower floors like plastic and fiberglass pans were available. These types of floors rarely leak as they are molded as a single piece. Tile floors, however, can be problematic. Removing a shower floor is a delicate process; it must be done correctly so you can install the new floor with no leaks, and without damaging the rest of the shower.
Shower doors allow the tub to be used for a long, relaxing soak and a quick shower. These shower doors are mounted on rails, which, in turn, are mounted to the tub and the walls. Whether for replacement or renovation, you might want to remove the shower door rail from your bathtub. The process isn't overly complicated and is a good project for a DIYer looking to get started with a bathroom project.
Walk-in showers provide a sleek, roomy alternative to cumbersome bathtub units and come in a myriad of styles and prices. Framed walk-in shower doors have a metal frame that stabilizes the door; unframed doors utilize thicker glass that slides freely with only a header and base track. Both have durable safety glass that breaks into large chunks upon high impact.
Replacing the cartridge or valve seats inside your shower faucet requires removing the handle. Often the handles on a shower faucet become stuck due to sediment build-up and corrosion. The best way to remove stuck shower handles is to use a faucet puller. You do not want to cause undue pressure on the house plumbing by banging on the shower handle to remove it from the wall. Faucet pullers ease the shower handle off the faucet without damaging the handle or plumbing. And they are available at home improvement centers.
Many people choose to remove chlorine from their shower water because of the health risks related to chlorine inhalation and ingestion through the skin. Risks include respiratory issues, skin and hair problems and eye conditions. According to HeartSpring, "chlorine is a toxic chemical." Benefits of reduced chlorine in shower water include less dry hair and skin. Install a shower nozzle filter to reduce or eliminate chlorine from your shower.
Shower doors wear out naturally with years of use and will need replacing. The hardest part about installing new shower doors may be removing the old shower doors and tracks. The tub and tile caulking sealant used to seal the door tracks from water leaks hardens like concrete over time and becomes difficult, though not impossible, to remove. The whole door and track removal process should take only a few hours for the average do-it-yourselfer.
Flow restrictors in faucets and shower heads save money by reducing the amount of flowing water. Often these devices clog with sediment resulting in low water pressure. Removing a shower flow restrictor from the shower head is slightly different than removing one from the faucet. Most shower heads use a semi-permanent flow restrictor. To remove the flow restrictor in a shower head requires breaking the flow restrictor.
When you want to replace your old shower door or just put up a shower curtain, you'll have to remove the existing shower door frame. The shower door frame fastens to the shower walls with screws. Often the only glue holding a shower door frame is the caulk you see at the wall seam. A shower door frame fits like a puzzle from the bottom up. When removing the frame, start at the top to disassemble the frame in reverse. It is a good idea to protect the bottom of the tub or shower, since you will be working inside…
Water with high levels of calcium leaves a chalky, white residue called limescale when it evaporates. Although limescale is not harmful, it does leave your shower screen looking dirty, even after a good scrubbing. You can buy chemical cleaning products made specifically to remove limescale but these products often are unnecessary. Before resorting to harmful chemicals, try some white vinegar and a little elbow grease to remove limescale residue.
The shower enclosure is one of the most important structures in your home. It protects your bathroom floor from water damage that can result in wood rot and very expensive repairs. After many years of service, you may feel the need to remove the door for a thorough cleaning. Done carefully, this can revitalize the look of your bathroom. There are two types of doors: sliding and swinging or pivot. Sliding doors are the easiest to remove. Pivot doors require a little extra care to avoid creating a mess.
Shower handles are often replaced due to breakage or discoloration from hard water. A new faucet may even come with a replacement handle that displays the logo of the manufacturer. In any case, the old shower handles have to come off before a new one can be installed. The hardware is easily accessed, but corrosion often makes it stubborn to remove. Lubricants and special tools help to remove stuck shower hardware so you can put on new handles yourself.
Delta shower faucets have a high temperature regulator that keeps you from being scalded should you accidentally turn the faucet too far to the hot side. The regulator is part of the shower cartridge. To remove it, you have to take out the entire cartridge, which uses a bonnet nut to secure it to the faucet body.
Although removing the shower handle on a Moen shower to gain access to the cartridge isn't difficult, the process depends on what type of handle you have. Moen makes several different kinds of handles. The handles mount in one of two ways: through a hidden screw in the top of the handle or a set screw located on the side of the handle.
Cleaning out a Delta drain system will require removing the strainer. The Delta shower tub strainer consists of a dome cover strainer and a drain plug. The dome cover is the surface piece you see that is most often referred to as the strainer. The drain plug is the portion of the drain that you normally see in a tub with a stopper. Removing the tub strainer will require using pliers in an unusual way.
When you have a rusty shower arm or you are replacing a head that ends up stripping the threads on the arm, you'll need to make a repair. Shower arms are available at home improvement centers. Use care when removing the original shower arm pipe. The shower arm pipe connects to the house plumbing, which is usually soft copper. Apply too much pressure on the plumbing and you'lll find yourself replacing more than a shower arm pipe.
When the shower doors on your tub are difficult to slide open, you will need to make some adjustments to the track or to the rollers on the door panel. To access the rollers you will need to remove the shower doors from the tub. Sliding shower doors secure to the door tracks using rollers and guides. Once you remove the shower door you can replace or repair the door system to get your doors working properly.
Single-lever showers that use a shower cartridge system make removal and replacement an easy task. The self-contained cartridge replaces the typical seal/spring combination of a ball-valve system, which may also be found in some single-lever shower faucets. While shower cartridges do have a long lifetime, they are not immune to wear and tear. If the shower handle will not turn off, or if drips and leaks occur, you need to remove and either clean or replace the shower cartridge.
Changing your shower knobs eventually is necessary in most homes. You may be replacing your shower knobs because you want a different look. The shower knobs may be out of date, or may be worn out. It is not a hard task, but sometimes very time-consuming. But it can be fun when you see the final outcome.
Whether you are considering converting your garage into an attached unit for a relative or on a rental house you own, you may find that it is a very smart financial move for several reasons. The resale value of the home to which you make this improvement should far outweigh the conversion cost, especially if you do the work yourself. If you hire someone to do the work, it should still be an excellent decision. In most areas, converting a garage to an in-law apt. is fine, as long as you obtain a permit from your local zoning office. There…
When parts on our showers are made of metal, it's inevitable we will find some rust. When that rust gets onto the shower door, it requires some extra attention in order to remove it. A few simple products and a little bit of elbow grease will have rust stains removed from your shower door in no time. You simply need to know which steps to take.
Kohler makes many styles of faucet handles to match just about any decor. When you need to replace or repair parts inside the shower faucet, you need to remove the handle. Although Kohler shower handles come in a variety of shapes and designs, they all come off in a similar way.
Shower doors are susceptible to water spots, particularly if they are not dried off after each use. Water spots on shower doors are unsightly and can diminish the appearance of the shower. Removing water spots from shower doors can be done using a variety of products and methods. Once the water spots are removed, drying your shower doors after each use will prevent them from coming back.
An unused corner shower can be taking up a great deal of space in a bathroom. Removing the shower can free additional space along two walls, making room for additional storage, or for installation of laundry appliances. Fortunately for homeowners, removing a corner shower is a simple job that requires just a little time and know-how to complete.
Accordion shower doors are constructed of plastic and hang on tracks located at the top and side of a shower. They fold in an accordion pattern to one side when not in use. Because they are more difficult to clean than other shower coverings, accordion doors are not very popular with homeowners. Many homeowners who have accordion showers doors choose to replace them with a more modern shower door. Removing the old door is not difficult and requires nothing more than common household tools.
Caulk is used to seal shower door frames to prevent water from leaking out around them. This is especially important if your walls are not tiled on the outside of the frames and if you have carpeted or wood floors. When you remove the shower doors and frames, caulk will still be on the shower or tub surround. Caulk sticks extremely well to most surfaces and will not pull off, and if you use the right tool, it is not a difficult process.
When it comes to your bathroom and shower door, it is essential to occasionally remove the old caulk and replace it. Since the caulk in the shower area is constantly wet, it easily develops mildew and mold. Using caulk with a caulking gun and making an even bead of caulk is a knack that every owner should acquire. If you get caulk on anything, the caulk will not harm it; however, it is important to get rid of the caulk for aesthetic reasons.
Build-up in showers is common, even with constant cleaning. Mold, mildew and a filmy residue from commercial cleaners can build up on the walls and floor over time, making the shower appear dirty even after you've just cleaned it. To help prevent this problem, use a few household items to make your own shower cleaners. They will destroy shower cleaner build-up and prevent it from coming back. Best of all, they're safer and more environmentally friendly than commercial cleaners.
Shower sealant, also called caulk, is commonly used to bond and hide the joints in bathtubs and shower tile. It is composed of a silicone-based adhesive that effectively prevents leaks, water damage and rusting. Removing shower sealant may seem difficult, but can be a simple process with the proper materials and cleaning method. Fortunately, an efficient adhesive solvent can help ease the process of dissolving silicone. Such a product is available at home improvement centers and hardware stores.
Water spots can commonly develop on shower doors from hard water stains, or simply from cleaning the wrong way or with the wrong ingredients. Luckily, you can take care of this mild problem with ease. Use the right products and clean effectively to make water spots a thing of the past.
Removing a shower surround may be a little difficult, but you can usually do it yourself. There are two options a shower surround can be installed, which will determine its removal method. One way is by screws and caulking and the other is by using adhesive and caulking. There are slightly different ways to removing these two types of shower surrounds, and all it takes is a few basic materials.
Stubborn scale deposits are ugly on any surface, especially shower doors. Over time, soap, grime and scale deposits build up and become more and more difficult to remove. You don't want to use a harsh chemical to remove scale deposits and you don't want to use a cleaning solution that has a strong odor. There is a way to remove stubborn scale deposits with some simple ingredients you have in your kitchen.
If the frosted designs on your shower doors have become outdated, you can probably remove them with a little effort. Frosting can be done using frosted paint, window clings or acid etching. These instructions only work for window cling frost designs. Acid etching actually eats into the glass and cannot be removed. Likewise, frosted paint requires scraping in ways that damage the glass surface permanently.
Shower doors are an attractive addition to any bathroom, but there may come a time when they need to be removed. Whether you prefer shower curtains or simply want to replace existing doors with a new set, this is a do-it-yourself project that can easily be accomplished in a single afternoon. Although removing the doors is not difficult, care should be taken not to damage the tub any more than is necessary during the removal. If you have a Fiberglas tub or tub surround, small screw holes will be left where the shower door tracks attach to the tub.
Removing unsightly water spots from glass shower doors is easy to do. Water spots are caused by dissolved minerals found in hard water, and they become visible when water evaporates and leaves those minerals behind. They often appear as a white, chalky substance and, if left on glass shower doors for extended periods of time, they can become etched into the glass permanently. Preventing water spots is as simple as using the squeegee on the glass on a regular basis to keep it clean and free of the damaging minerals found in water. If you already have water spots on…
Removing three -shower fixtures is relatively simple. The tools that you will need are basic hand tools. Once you have removed the first handle, the other two handles will come off exactly the same way as the first one did. You should be able to remove all three handles in less than 15 minutes.
Removing a shower base, or the pan, is not difficult. Removing a shower base is just the opposite of installing one. Removing a hand-framed base is a little more complex than a prefabricated pan, but most shower bases consist of a ready-made fiberglass or acrylic pan that is simple to remove.
The two-word phrase: "shower base" describes the basin of a shower stall, used to keep water from spilling out onto the bathroom floor. Shower bases may be made from plastic, fiberglass, tile, porcelain or metal and may be circular, rectangular, square, oval or polygonal. Often, the shower base is built into the shower stall, making it possible to remove the entire stall to remove or replace the base.
If you need to make a repair to a leaky shower-arm, or you simply want to make a change for cosmetic reasons, you can probably make the repair or replacement by yourself. You don't need to be a skilled plumber to remove the shower-arm, and you'll need just a few household tools and a small window of time. If the pipe and hardware are old and corroded, you might need to use a little more elbow grease, and perhaps some lubricating oil, but you will probably be able to remove the arm without hiring a professional.
Mildew is a fungus that grows in damp places and therefore, is why many homeowners struggle with keeping mildew under control in their bathroom. Even if you clean your bathroom weekly and spray a shower mist after every use, you may still see the black stuff start to grow. Sometimes, it is on the seal of your shower door which is often a forgotten place or not easily seen. Since the door is usually closed, moisture often stays there for long periods of time, which is a haven for mildew growth.
If you are in the mood to do some remodeling in your bathroom and are ready to get started, one of the first things you have to do is remove the old stuff. Some items you can save, such as the glass shower door, the sink and the toilet. Care should be taken when removing a glass shower door so that it can be used again--or just so that you don't break the glass and make a mess of your bathroom. If you clean it up well, you may be able to sell it and your other bathroom items either…
There are several kinds of showers. There are those that include a tub while others stand alone. Using shower fixtures allows us to adjust the water to hotter or colder along with the pressure. Removing the shower fixtures may be needed if you desire a new shower head and new handles or if you are experiencing a leak or drip from your shower head.
Pesky hard water spots on a shower door can be very frustrating. Unable to be removed by regular cleaning products, these hard water spots can build up over time and cause your shower door to look grimy and dirty even just after it's been cleaned.
Soap scum and chalky white buildup on your shower doors makes your otherwise clean bathroom look dirty. The chalky white buildup is lime scale. This occurs because of hard water and humidity. Just like soap scum, lime scale is resistant to cleaning with standard glass cleaner. It is necessary to break down the scale with acid to remove scale from the shower doors. Fortunately, the acid remover necessary is probably already in your kitchen pantry. This not only removes scale but also the soap scum buildup on your shower doors.
