×
Back Button

How to Make a Bunkie Board

Lorna Hordos

Making a bunkie board is a relatively simple project, especially if you're handy with a circular saw. If not, have the lumberyard cut the board to size.

Slat-style beds without box springs -- such as bunk beds and certain platform beds -- can be downright uncomfortable when paired with basic foam or other insubstantial or thin mattresses. A bunkie board remedies this discomfort. The fabric-wrapped plywood base provides just a little height and, more importantly, a bit more structure or a flat surface to eliminate the bumpy feel transferred by the slats. Also, the board reduces wear on the mattress caused by friction or rubbing that otherwise occurs between it and exposed slats.

    Measure the Frame

  1. Remove the mattress. Measure the bed frame area between the side and end rails occupied by the mattress. Subtract up to 2 inches from the width and length -- in other words, an inch from all four sides. This will be the bunkie board size; adjust it accordingly -- the shortened size allows room for the wraparound padded fabric that softens the bunkie board's edges and surface, making them less likely to puncture or damage the mattress. So, the thicker the padding, the smaller the board.

  2. Cut the Plywood

  3. Cut the 3/4-inch plywood to the determined size, using a circular saw and carbide blade designed for plywood to avoid splintering. If your twin-sized bed or twin bunk-bed frames each measured 38 by 75 inches, for example, you may want to cut the board to 36.5 by 73.5 inches, allowing an inch and a half on each span for moderately thick upholstery-grade quilted fabric.

  4. Tip

    If you aren't comfortable using a circular saw, check with the lumberyard where you plan to get the plywood; often it can cut lumber to size for you, so have the measurements ready.

    Sand It Smooth

  5. Abrade the board's edges and any roughness on the top and bottom sides, using medium-grit sandpaper. A power sander makes relatively quick, easy work of a large plywood-sanding project. If the wood is at least somewhat smooth, it's less likely to cause wear or come through the material over time.

  6. Cut the Quilted Upholstery Fabric

  7. Spread out the quilted upholstery smoothly on the floor or other large work surface, wrong side up, if applicable. Cut two pieces -- one for the top and one for the bottom of the bunkie board, using scissors. Although the bottom one can measure the board's exact width and length, the top piece should be a few inches longer on each side to wrap around the plywood, overlapping the fabric on the bottom for stapling.

  8. As an example, if you're making a full-sized bunkie board at 53 by 74 inches, cut the bottom fabric to this size, and the top piece to about 59 by 80 inches, leaving a few inches on each side for stretching around.

  9. Tip

    To save money, use quilted fabric just on the top side of the bunkie board, and inexpensive dust-cover material on the bottom.

    Apply the Glue

  10. Spray the plywood's upward-facing side with fabric adhesive. Smooth the exact-fitting bottom upholstery or dust-cover over the board, centering it lengthwise and widthwise. Flip the plywood over. Spray the board's now-upward facing side with adhesive. Lay the slightly over-sized piece of fabric smoothly into place, centering as with the other side, and folding and stapling each corner.

  11. Warning

    As with using any adhesive, open windows for ventilation, and refer to the warnings on the label for any other precautions.

    Tip

    Having someone help you apply the fabric is easier than doing it alone, especially if you're working with a king-size bunkie board.

    Finish With Staples

  12. Fold and staple the excess quilting onto the board rather than trimming it, to secure the overlapped edges and corners, and for a more padded finish.

The Drip Cap

  • Slat-style beds without box springs -- such as bunk beds and certain platform beds -- can be downright uncomfortable when paired with basic foam or other insubstantial or thin mattresses.
  • A bunkie board remedies this discomfort.
  • The fabric-wrapped plywood base provides just a little height and, more importantly, a bit more structure or a flat surface to eliminate the bumpy feel transferred by the slats.
  • If your twin-sized bed or twin bunk-bed frames each measured 38 by 75 inches, for example, you may want to cut the board to 36.5 by 73.5 inches, allowing an inch and a half on each span for moderately thick upholstery-grade quilted fabric.
  • Spray the plywood's upward-facing side with fabric adhesive.