How to Replace the Drain Pump on an LG Front-Load Washer

Save

When a LG front-load washing machine fills, a valve opens on the machine and allows the water to flow into the tub. Once the wash cycle is complete, the water drains from the tub with the assistance of a pump. The water cannot drain from the washtub without the assistance of this pump, so if it goes bad, you need to replace it. Replacing the water pump on the LG front-load washer is not difficult, so there is no need to call in a technician to make the repair. All you need to do the job is a few simple tools found in most home toolboxes.

Things You'll Need

  • Phillips screwdriver
  • Needle-nose pliers
  • Wooden block
  • Channel-lock pliers
  • Rags
  • Unplug the washing machine power cord from the electrical outlet. Pull the machine away from the wall to gain access to the back. Remove the two screws on the back of the machine holding the top on using a Phillips screwdriver. Pull the top toward the back and lift it off the machine. Pull the soap dispenser drawer out of the machine.

  • Depress the button at the back of the soap dispenser to release the clip. Pull the drawer out of the slot. Remove the screws holding the soap dispenser bracket in place using a Phillips screwdriver. Remove the two screws securing the control panel to the front of the machine using a Phillips screwdriver.

  • Push down on the locking tabs at the back of the control panel and lift it from the front of the machine. Lay the control panel on top of the machine out of the way. Open the washing machine door. Grasp the spring clamp using a pair of needle-nose pliers and pull it away from the door gasket.

  • Lift the gasket away from the door opening and push it inside the washing machine. Be careful when doing this, as the edges of the door opening under the gasket are sharp. Raise the front of the washing machine off the floor. Place a wooden block under the machine to prop it up.

  • Remove the screws from the bottom of the front panel of the LG washing machine using a Phillips screwdriver. Remove the block from under the washing machine and lower it to the floor. Remove the screws from the top of the front panel with the Phillips screwdriver. Pull the front panel away from the washing machine frame.

  • Disconnect the wire harness from the front panel of the LG washing machine and set the panel aside out of the way. Reach under the washing machine tub and disconnect the hose from the pump using a pair of channel-lock pliers to squeeze the clamp. Release the clamp on the drain hose using the channel-lock pliers and pull it away from the pump.

  • Clean water spillage from the hose using rags. Depress the clip on the pump wiring harness and unplug it from the pump. Remove the mounting screws from the pump using a Phillips screwdriver. Pull the pump out of the LG washing machine. Place the new drain pump in the washing machine and install the mounting screws with the screwdriver.

  • Plug the wiring harness into the new drain pump. Connect the drain hose using the channel-lock pliers to squeeze the drain hose clamp to open it. Push the hose onto the pump firmly and release the pliers to lock the clamp. Install the inlet hose to the pump squeezing the clamp open with the channel-lock pliers. Release the pliers to lock the clamp in place.

  • Move the front panel into place in front of the LG washer and plug the wiring harness into the front panel. Place the panel on the washing machine frame and install the top retaining screws using a Phillips screwdriver. Lift the machine off the floor and prop it up with the wooden block. Install the bottom screws using the Phillips screwdriver.

  • Remove the block from under the machine and lower it back to the floor. Open the door of the washer and press the boot seal into place around the door perimeter. Close the door on the washing machine. Place the control panel on the front of the machine and press firmly to lock the retaining clips into place. Install the screws with the screwdriver.

  • Place the top panel on the machine and install the retaining screws using the Phillips screwdriver. Install the soap drawer bracket and tighten the screws with the Phillips screwdriver. Install the soap dispenser in the front of the LG washing machine. Plug the power cord in and push the washing machine against the wall.

Tips & Warnings

  • Never service an LG front load washing machine or any other appliance without first removing the power source.

References

Promoted By Zergnet

Comments

You May Also Like

Related Searches

Check It Out

22 DIY Ways to Update Your Home on a Small Budget

M
Is DIY in your DNA? Become part of our maker community.
Submit Your Work!