End caps glue on PVC water lines. There are two ways to cap a copper water line. (Water lines are apart from cast-iron water mains.) The easiest way for non-plumbers to cap a copper line is with a "Sharkbite" end cap made by the Cash Acme subsidiary of the Reliance Worldwide Corporation. Most hardware stores and home improvement centers sell Sharkbite fittings. They should be legal to install under your local plumbing code, but they might not be. So if you want to conscientiously adhere to all local plumbing codes, you may have to solder an end cap to your copper water line, and there is a little technique to that.
Things You'll Need
- Adjustable pipe cutter
- Metal file (for copper lines)
- PVC, Sharkbite or copper end cap (depending on your line and local plumbing code)
- PVC cement (for PVC lines)
- Heat gun (for soldered end caps)
- Flux paste (for soldered end caps)
- Wire solder (for soldered end caps)
- Propane torch (for soldered end caps)
- Matches (for soldered end caps)
- Wire brush (for soldered end caps)
Turn off the water to your house at the main valve. Open all faucets.
Cut the line you want to cap with an adjustable pipe cutter. Remove any burrs from the end of cut copper lines with a metal file.
Glue a PVC end cap to PVC water lines with PVC cement. Push a Sharkbite end cap onto the end of cut copper lines where plumbing codes allow. Sharkbite fittings are self-adjusting and self-adhering.
Thoroughly dry the inside of cut copper lines that are to be fitted with soldered end caps using a heat gun. Steam prevents the proper installation of soldered end caps.
Clean the outside of the pipe and the inside of the end cap with emery cloth until both surfaces shine. Apply flux paste to the inside of the cap and to the cut pipe with your fingers. Slide the end cap over the end of the pipe.
Unroll about 3 inches of wire from a roll of solder wire. Light a propane torch with a match and adjust the gas flow until the torch flame is blue.
Heat the pipe and fitting with the torch. Touch the solder to all sides of the copper pipe when the flux begins to bubble. Ensure that the solder flows into the joint. If the solder does not flow into the joint, the pipe is still wet and steam is pushing the solder out.
Heat the end cap until the joint fills with solder and solder begins to accumulate outside the fitting. Remove excess solder with a wire brush.
Turn on the main water valve. Check the end cap for leaks.
Turn off all faucets. Recheck the end cap for leaks.
- Cash Acme: Sharkbite Connection System
- "The Complete Guide to Plumbing"; Creative Publishing International; July 2008
- Handyman Home Repair Tips: Tips for Repairing Copper Water Pipes
- Synergy House: Sweating Pipes the Right Way
- Practical Repairs: How to Sweat Copper Pipe
- Home Improvement Zone; Soldering Copper Pipes; 2011
- Photo Credit Comstock/Comstock/Getty Images
Types of Copper Pipe Fittings
Copper pipe and fittings have been used in homes and buildings for decades. Copper is not a cheap material but it is...
How to Stop Water Hammering in Pipes
If water pipes bang loudly when a faucet is shut off, it may be due to a condition known as water hammering....
How to Make a PVC Pipe Water Cannon
Water wars are a refreshing way for kids to stay active and cool on a hot summer afternoon. Forget about the squirt...
How to Remove an End Cap From a PVC Pipe
Forward-thinking builders or DIY-oriented home owners will often add dead-end pipes for water or drain lines to facilitate plumbing future additions, appliances...
How to Replace a Three-Handled Tub Faucet
Replacing your old, worn-out three-handle tub shower faucet, with a new model will improve the bath&#039;s appearance. Gaining access to the faucet...
How to Cap a Residential Sewer Pipe
Residential sewer pipes are generally made of either Acrylonitrile Butadiene Styrene (ABS) or PVC hard plastic. Both types of pipes are very...
How to Cap a Copper Refrigerator Water Line
If you plan to disconnect and remove your ice maker either for repairs or permanently to make more freezer room, capping the...
Problems With Steam Mops
A steam mop uses steam to clean carpets and floors. Most steam mops have a small water tank, where the water is...