Unplug the Black & Decker Grass Hog trimmer from the extension cord. Allow the trimmer head to completely stop rotating before attempting to change the line. Place the trimmer upside down on a flat surface so that the trimmer head is facing up.
The Black & Decker Grass Hog is one choice for taking care of trimming jobs in your yard. The Grass Hog is an electric trimmer suitable for smaller yards. As with most grass trimmers, the line requires replacement from time to time. However, unlike most trimmers, the Grass Hog does not use a bump feed. Changing the string in an automatic-feed Black & Decker Grass Hog is a simpler job than on most trimmers. Replacement line kits for the Grass Hog are available at most home improvement centers and Black & Decker dealers.
Things You'll Need
- Black & Decker .065 replacement line pack
- Utility knife
Press the two tabs on the side of the trimmer line cartridge with your fingers. The tabs are between the two holes where the line feeds through the housing. Lift up on the cartridge while pressing in the tabs and remove the cartridge from the housing.
Turn the cartridge over so that the line spool is facing up. Lift the line spool out of the cartridge. Look at the lever in the bottom of the cartridge. It should remain flat and the teeth should be inside the center teeth, much like the teeth of two gears. Adjust the lever as necessary so that it is flat in the housing if it becomes dislodged when removing the line spool.
Remove any remaining line from the spool and discard the line. Hold the spool in one hand with the slot cut-outs facing up. There are two channels for the cutting line on the spool. Each channel has an anchor hole in the side.
Insert the end of one line from the replacement line kit into the anchoring hole on the upper channel. Wind the line around the spool in the direction of the arrow on the spool. Maintain tension on the line as you wind, and wind the line evenly in layers.
Continue winding until the line reaches the recess cut-out on the top of the spool. Cut the line with a pair of scissors or utility knife. Weave the end of the line into the nearest slots on the spool. Repeat the winding process on the lower channel with the next piece of line. There is a recessed cut-out on the bottom of the spool to determine when to cut the line and slide the opposite end into the slots opposite the first line.
Place the spool into the cartridge with the line ends pointing away from the cartridge. Rotate the spool as necessary until it sits flat in the cartridge. Unhook one of the line ends from the spool holding slot and insert the end through one of the eyelets on the housing. Repeat for the opposite line.
Line up the tabs on the cartridge with the slots on the housing. Press the cartridge into the housing until the tabs lock into place.
Tips & Warnings
- There are also pre-wound replacement spools available so you don't have to wind the new line yourself.
How to Wind the Spool on a Black & Decker GrassHog XP
Instructions. 1. Unplug the GrassHog and lay it on a flat surface, ... The Black & Decker Grass Hog is one choice...
How to Refill the Trimmer Line for Model Number GH700
How to Change the Double String in a Black & Decker Grass Hog. ... The Black & Decker Grass Hog is one...
How to Restring a Black & Decker Weed Eater
Managing weeds in your lawn doesn't have to be time consuming, especially with the aid of a weed eater. However, when your...
How to Replace the Line on a Black & Decker 8207 Trimmer
How to Replace the Line on a Black & Decker 8207 Trimmer. ... How to Change the Spool on a Black &...
How to Troubleshoot a Black & Decker Electric Hedge Trimmer
How to Change the Battery in a Black & Decker Cordless Trimmer; Print this article; ... The Black & Decker Grass Hog...
How to Replace Wire on Black & Decker Whipper Snipper
Unplug the Whipper Snipper's power cord to avoid injury while replacing the wire spool. 2. ... How to Replace the Line in...
How to Thread a Black & Decker ST6000
The Black & Decker GrassHog XP is a trimmer and edger used for yard work. ... How to Replace the Line in...
My Black & Decker Weed Eater Feeding Line Is Not Working
The Black & Decker weed eater uses a spring and a bump spool to automatically feed out more line when you tap...