A hexagon has six sides and six corresponding angles. Each angle is 120 degrees and the sum of the angles is 720 degrees. A wooden hexagon made from six different pieces of wood will follow this rule. Cutting a 60-degree angle on each end of all six pieces results in six pieces of wood that will fit together and form a hexagon. You may cut the six pieces and angles for a wooden hexagon on a miter saw using a custom fixture.
Things You'll Need
- 1-by-4 lumber, 15 in. long
- 3/4-in. plywood,15 by 15 in. square
- Drill with bits and screwdriver bits
- Wood screws
- Tape measure
- Power miter saw
- Wood pieces
Large-Angle Miter Saw Fixture
Place one edge of the 1-by-4 against the face of the plywood flush with the edge of the plywood and clamp it in place.
Drill four 5/64-inch pilot holes for the wood screws through the plywood bottom and into the 1-by-4 piece. Space the pilot holes three inches apart and one and one-half inches from the ends. Fasten the plywood to the 1-by-4 by screwing the wood screws through the pilot holes and into the 1-by-4.
Remove the clamps from the custom fixture. Place the fixture on the miter saw table with the 1-by-4 against the fence. Without starting the motor, lower the blade into the table slot and slide the fixture against the blade. Hold the fixture in place and raise the blade.
Clamp the 1-by-4 on the fixture to the miter saw fence with clamps. The plywood edge perpendicular to the fence will act as a new fence for cutting complementary angles greater than 45 degrees. For example, to cut a 60-degree angle, set the miter saw table to 30 degrees with the adjustment handle of the table pointing away from the custom fixture. Place your workpiece on the table against the custom fixture. The angle cut into the workpiece will be 60 degrees.
Cutting Hexagon Angles
Remove the custom fixture from the miter saw. Set the power miter saw table at 90 degrees. Measure and mark the wood to cut six pieces one-eighth inch longer than the final length required. Place the wood on the miter saw table and hold it firmly against the fence. Start the saw and lower the blade into and through the wood at the marks to make the cuts.
Install the custom fixture on the miter saw table as shown previously. Set the miter saw table to 30 degrees away from the fixture. Place a hexagon side on miter saw table with the edge against the fixture fence. Align the blade with the end of the workpiece corner to cut the angle without altering the length of the piece. Clamp the workpiece to the fixture. Start the blade and cut the angle into the wood.
Flip the workpiece end over end so the uncut end is now facing the miter saw fence. Align the blade to cut the piece as before without altering the length of the piece. Clamp the piece to the fixture. Start the saw and cut the angle onto the end of the wood. Repeat these steps for all six pieces.
Check the length of the pieces for accuracy. You can adjust the length of each by cutting very small amounts off the end of each piece with the saw.
- "Fine Woodworking Magazine"; Cut All Angles on the Miter Saw; Richard Menin; June 1996
- Photo Credit Hemera Technologies/PhotoObjects.net/Getty Images
How to Make a Hexagon Deck Platform
For something more sophisticated than a rectangle or a square, make your new deck hexagonal in shape. A regular hexagon, with its...
How to Cut a Hexagon With a Table Saw
If you have a project that requires accurately sized and proportioned hexagons, follow these steps for a precise method to draw a...
How to Find Degrees in Polygons
A polygon is a closed two-dimensional shape composed of three or more connected line segments. Triangles, trapezoids and octagons are common examples...
How to Figure Degrees in an Octagon
An octagon is an eight-sided shape, such as a stop sign. Octagons can be regular or irregular. A regular octagon has sides...
How to Find an Angle of a Hexagon
A hexagon is a shape with six sides. Using the correct equation, you can find the degree of each of the interior...