How to Attach Hardware to a Fiberglass Boat

Save

Water might be the environment that boats operate in, but water can be the most destructive ingredient when it comes in contact with foam or balsa deck and hull cores. Leaking water can react to the resins and adhesives in fiberglass core material and cause a chemical reaction that melts and deforms the core. Serious fiberglass delamination results. The reason for the destruction commonly points to the inefficient technique used to attach the hardware to the fiberglass boat. Any boat owner can follow some easy steps and use a few special products to protect his boat against thousands of dollars in damage.

Things You'll Need

  • Dish washing soap
  • Bucket
  • Brush
  • Rags
  • Hardware piece
  • Felt pen
  • Scratch awl
  • Masking tape
  • Drill motor
  • Drill bits
  • Aluminum back plate (1/8- or 3/8-inch)
  • Marine plywood (3/8- or 3/4-inch -- optional)
  • Hack saw
  • Bolts, lock-washers, spacers (stainless steel)
  • Adhesive caulk (polysulfide)
  • Spatula
  • Socket set
  • Ratchet wrench
  • Assistant
  • End wrenches
  • Mix dish washing soap in a bucket of water. Use a cleaning brush to scrub the area where the hardware fitting will mount. Remove all oil, grease and wax. Dry the area with clean rags. Set your piece of hardware over the surface where you want it mounted. Align it properly. Mark an outline of the hardware piece with a felt pen on the deck or fiberglass surface.

  • Use a scratch awl to stick down into the mounting holes of the hardware to mark the drill holes in the deck or surface. If hardware needs to be mounted above deck, look under deck for the proper clearance needed to attach the nuts and backing plate. Apply masking tape all around the perimeter of the hardware piece you outlined with the felt pen. Extend the tape out a few inches in all directions.

  • Take a piece of aluminum backing plate, which measures 1/8-inch thick (for a small-stressed hardware piece) and cut a section out with a hacksaw, large enough that it will accept the drill holes of your hardware piece. Size the backing plate under the deck (or underside of the top surface), to make sure it will fit and lay flat. Place your hardware piece over the backing plate and mark the drill holes with the scratch awl.

  • Use the drill motor and appropriate bit to drill the holes in the backing plate that match the hardware piece. Open a can of polysulfide adhesive caulk and dab a liberal layer over the top of your marked area with a small plastic spatula. Put a coating of adhesive caulk on the underside of the hardware piece.

  • Use the spatula to apply a layer of caulking adhesive on one side of the backing plate. Instruct an assistant to take the backing plate below deck or hold it to the opposite contact side of the mounting area.

  • Instruct the assistant to align the backing plate with the drill holes, placing the caulked side face up against the underside of the deck. Tell him he should put on one spacer, one lock washing and one nut (in that order) onto the bolt threads when they appear on his side.

  • Place the hardware piece in position over the drill holes. Coat the bolt threads (or screw threads) with caulking adhesive. Push the bolts down through the hardware piece. Have your assistant secure the spacers, lock washers and nuts on the ends of the threads. Have your assistant tighten the nuts by hand and them hold the nuts steady with an end wrench. Use a socket and wrench to tighten the tops of the bolts, but screw them in only snug-tight with medium pressure.

  • Scrape the excess adhesive caulk away from the seam underneath the hardware piece with the spatula. Remove the masking tape. Wait one week for the adhesive caulk to dry and cure. Then re-tighten the hardware piece bolts with firm pressure. This will seat the hardware piece into the adhesive caulk, which has now formed a gasket.

Tips & Warnings

  • You can use 3/8-inch marine plywood as a backing plate for small stressed hardware pieces. For stanchions and heavy cleats on a large power or sailboat, use 3/4-inch marine plywood as a backing plate. If you want to use aluminum for very heavy hardware stress points, obtain aluminum backing plate that measures 3/8-inch.
  • Always use through-bolts and backing plates to attach any piece of hardware to a fiberglass boat. Screws, even if they come with the hardware piece, will tear out of the fiberglass material when subjected to even the lightest stress. Use extra-large washers to distribute the torque stress.
  • Use some acetone and a rag to remove any traces of adhesive caulk that might have stained your deck.

References

  • Photo Credit Jupiterimages/Photos.com/Getty Images
Promoted By Zergnet

Comments

You May Also Like

  • How to Paint a Fiberglass Boat

    Fiberglass boats come new with a colored gel coat, not actual paint. Gel coats eventually fade and can not be cleaned or...

  • How to Make a Balsa Wood Box

    Balsa wood is a popular wood for small handcrafting projects because it is lightweight and soft enough to cut easily without the...

  • How to Attach Metal to Fiberglass

    Metal and fiberglass are completely different materials in every aspect. Attempting to join these two dissimilar materials may seem nearly impossible. However,...

  • How to Repair a Foam Core Boat

    A foam core boat combines two thin, high-strength, high-density skins and a low-destiny, low-strength, thick foam core. In this sandwich-style construction, the...

  • How to Mount a Seat in a Fiberglass Boat

    Two types of seats typically are found in boats, bench seats and pedestal seats. Usually, a bench seat is used at the...

Related Searches

Check It Out

How To Travel For Free With Reward Points

M
Is DIY in your DNA? Become part of our maker community.
Submit Your Work!