Many houses today are built with prefabricated roof trusses rather than joists and rafters. Trusses let a factory do much of the work; trusses are rafters with a bottom plate rather than a joist and with internal bracing built in. Rafters are still used, however, because they can provide more open space in an attic and are handy when building a shed or other outbuilding. The secret to a good rafter is cutting proper angles. And the secret to cutting correct rafter angles is the speed square, invented in 1925 by carpenter Albert J. Swanson.
Things You'll Need
- Speed square
- Rafter table
- Circular saw
Determine the width of the building, the rafter span, and the length, for the number of rafters needed. Choose or determine a pitch, the angle at which the rafters rise. Divide the span by two to get the rafter run, the length each rafter must cover. For a 24-foot wide building, the run would be 12. Pitches are measured in inches per foot; a 5/12 roof slopes up 5 inches for every 12 feet of run. Space rafters 24 inches apart, so a 30-foot long building will need 15 rafters.
Mark the top or plumb cut first. Put the pivot point of the speed square, a small hole (marked "pivot") where the straight side of the square meets the side with the lip on it, at the top edge of a rafter board. Move the square until the table on one side of the rectangular slot in the square is at the right pitch (5) on the top of the board; use the table marked "Common Top Cut." That will make an angle at the end of the rafter board for the plumb cut. Go back after rafter length is set and cut another 3/4 inch from that plumb cut, to allow for a 2-inch ridge board where opposing rafters meet.
Use a rafter table, which comes in an instruction manual with the speed square, to determine the length of the rafter. For a 5/12 rafter, that will be 13, or 13 inches of rafter for every foot of run; with a 12-foot run, that is 13 feet. Mark that spot and use the square to mark 1 inch in from the bottom of the board and 3 1/2 inches down from that mark to make a triangle, a notch called a birdsmouth where the rafter will rest on the top plate of the wall. Some speed squares have a diamond-shaped opening which can be used to calculate this, using instructions in the reference manual.
- Popular Mechanics: How To Use a Speed Square
- Quality Distributing: The Original Rafter Square
- Homebuilding Information and Planning: The Speed Square
- Homebuilding Information and Planning: How to Cut Common Rafters
- Stuff: How to Use the Swanson Speed Square
- Stuff: How to Use the Speed Square for Rafter Cuts
- Photo Credit Jupiterimages/Photos.com/Getty Images
How to Calculate Rafter Length With a Framing Square
Calculating the length of a rafter and the angles to cut the rafter ends at requires either a lot of geometry or...
How to Build Roof Rafters Using a Framing Square
At first glance, determining the length and angles for cutting roof rafters seems like a complicated process. The key to accurately cutting...
How to Use a Rafter Square
A rafter square, or rafter angle square, is a measurement tool used in carpentry. It is triangular in shape and combines elements...
How to Calculate Angles in Carpentry
Building a roof or cutting stringers for a stairway requires finding angles, marking and cutting them correctly. In carpentry, you usually do...
How to Cut Bird's Mouths in Rafters
Prior to factory-made trusses and metal rafter brackets, every framing carpenter knew how to cut a "bird's mouth" or "bird's beak." A...
How to Measure Roof Pitch With a Speed Square
The Swanson Speed Square is a popular tool with most carpenters. The triangle-shaped "square" was invented in 1925 by Albert Swanson to...
How to Measure an Angle With a Speed Square
A speed square is essentially a triangle-shaped ruler used for calculating angles or as a straight edge. A speed square has a...
How to Use a Carpenter Square
Understanding how to use, care for and store a carpenter square are discussed in this free educational video series.
How to Set an Angle with a Speed Square
In addition to the 90-degree and 45-degree angles so simple to scribe from an angle, you can also use a speed square...