Vapor lock can affect any kind of engine during normal operation where the outside ambient temperature remains high, or the fuel system becomes overheated because of high engine temperatures or lack of insulation. Fuels that have high volatility can also cause vapor lock. When fuel boils inside a metal line or carburetor, it vaporizes, which causes a halt of the fuel delivery. This condition can cause an engine to stall or refuse to restart, even with a perfectly running engine. Preventing vapor lock requires some observation of the existing fuel delivery system, along with some modifications.
Things You'll Need
- Socket set
- Ratchet wrench
- Fuel line wrenches
- Fuel inlet adapters
- Neoprene or impregnated fabric fuel line
- Pipe cutter
- Wire cutters
- Hose clamps
- Reflective heat insulation
- Heat-resistant tape
- Boat owner's manual (if applicable)
- Fuel filter (if applicable)
- Stiff cleaning brush
- Carburetor base gasket spacer (optional)
Place the transmission in park or neutral, depending upon the type of transmission. Set the emergency brake and raise the hood. For any other engine applications, remove the engine cowl or case cover by unclasping the hood snaps. For boats, unclasp the cowl snaps by hand and pull the cover off. Some boat engine cowls might require you to use a socket and wrench to remove the bottom latch bolts.
Examine the fuel line routing, particularly the metal lines that attach to the carburetor or fuel rail -- injected systems. Any metal fuel line that sits directly over the intake manifold or in proximity to the exhaust manifold will serve as a high heat sink. Use a pipe cutter to remove as much metal line as possible. Leave enough of the original line to attach a hose.
Replace the metal line with neoprene impregnated fabric line or hose, by pushing it onto the cut end of the metal line. In the case of a fuel inlet, use a fuel line wrench to loosen the nut and remove the line completely. Screw an adapter into the fuel inlet that has a hose nipple on the end. Use wire cutters to cut the appropriate length of hose you need. Attach the hose with hose clamps; tighten the clamps with a screwdriver. Route the hose properly, keeping it up away from heat sources.
Use scissors to cut strips of reflective heat insulation fabric that you can wrap around your fuel lines. You can wrap metal fuel lines or neoprene lines. Cut the lengths required to cover as much line as possible and tightly wrap them around the fuel line. Secure the insulation fabric with heat-resistant tape, by wrapping it around the insulation fabric several times.
Avoid using fuels that have a high volatility rate, which consist of fuels that have extra alcohol content. In the case of a marine engine, find out what your rated Reid Vapor Pressure states in your owner's manual. Drain your gas tank at the petcock valve with a socket, and then refill the tank with a lower RVP rating. This will reduce the volatility of the gas and ward off vapor lock.
Change the fuel filter by removing the filter hose clamps with a screwdriver. Disconnect the filter from the hoses and attach a new filter to each hose end. Tighten the hose clamps with a screwdriver. For metal in-line fuel filters, use a fuel line wrench to disconnect the fitting on both ends. Screw the fittings onto the new filter with a fuel line wrench. A new filter will increase fuel volume. Look for any sharp bends or kinks in the fuel line and straighten them out or replace the line.
Remove the radiator cap and check the engine coolant. Add water or coolant if the radiator is low. The thermostat and cooling fan must be in proper working order -- an engine that runs hot will vapor lock more readily. On marine engines, clean all obstructions from the engine cowl vents with a stiff brush. Use a stiff brush to clean all debris away from the radiator fins on automotive vehicle, such as road debris, plastic, leaves and insects.
What Makes a Car Stall in Warm Weather?
Nothing is more frustrating to a motorist when his or her vehicle stalls. The stalling may result from a fuel or a...
How Do I Repair a Vapor Lock?
Vapor lock is rare in newer cars because of the modern fuel injection systems but is common in older carbureted cars. Vapor...
How to Stop Vapor Lock in an Outboard
Vapor lock is the bane of summer for boaters. Parts of an outboard motor's fuel system are cooled or vented to prevent...
How to Wrap a Fuel Line
An automobile or marine engine's rubber fuel line feeds gasoline from the gas tank into an engine's carburetor system. Before modern fuel...
How To Use Clothespins for Vapor Lock
Vapor lock happens when gasoline evaporates in an engine, usually in the fuel line, fuel pump or the carburetor. The fuel pump...
How to Stop Vapor Lock in Plumbing
When a faucet is closed suddenly, air becomes trapped in the plumbing. High water pressure then compresses the trapped air to a...
The Leaf Blower Stops Running After It Warms Up
A gas-powered leaf blower uses a combustion engine to generate power. Normally, when this engine burns gas, the vapors and heated gases...
Why Does my Lawn Mower Engine Stall When it Gets Hot?
As the lawn mower engine burns gas inside the cylinder it generates an enormous amount of heat. This heat must disperse out...
What Is an Air Lock in Plumbing?
Air lock in your house’s plumbing will leave a water line nearly or completely useless until you fix the situation. You may...
What Causes Vapor Lock in Gasoline Tractor Engines?
Vapor lock occurs when the gasoline being supplied to an engine that typically, but not exclusively, uses a carburetor becomes overheated and...
Tricks & Mods for a Toyota Corolla
The Corolla is a popular line of compact cars manufactured by Toyota, a Japanese car manufacture. It has been the best selling...