DIY Hanging Bed

Save

A hanging bed is an ideal way to save space in small areas. You can hang the bed with enough room under it for another bed, or even a desk area. Whatever pattern you choose, hanging beds are an easy way to get creative by using small spaces efficiently. And don't let the potential sway scare you off. Adjusting the angle of the chains or cables holding the bed to reduce the side-to-side sway.

Things You'll Need

  • 2 side pieces, 2-by-8-by-81 inches
  • 2 end pieces, 2-by-8-by-41 inches
  • Wood glue
  • Box of 2 1/2-inch pocket hole screws
  • 4 braces, 2-by-4-by-41 inches
  • Tape Measure
  • Pencil
  • Plywood bottom, 32-by-40-by-75 inches
  • Box of 1/4-inch wood screws
  • 12 lag eye bolts, 3/8 inches by 4 1/2 inches
  • 4 lengths of 3/16-by-9-foot chain
  • 8 quick links, 5/16 inches
  • Drill with bits
  • Screwdriver
  • Sander with sandpaper
  • Sawhorses
  • Paint or stain
  • Attach one end piece to one side piece at a right angle, with the end piece flush with the length of the side, using wood glue and five pocket hole screws. Attach the other side piece to the opposite end of the end piece at a right angle using wood glue and five more pocket hole screws. Attach the last end piece to the ends of both side pieces, with the sides flush to each end of the end piece, using wood glue and five pocket hole screws on each joint. Sand and then paint or stain the frame as desired.

  • Attach the braces to each end piece with six pocket hole screws on the outer sides of the frame and three to each outer end. Line the braces up against the end pieces flush with the bottom edge of the side pieces.

  • Measure 36.5 inches from the edge of one of the braces and make a mark. Measure 36.5 inches from the mark and make another mark. On the outside of the frame, measure from the edge of the frame 42.5 inches and make a mark, from that mark measure 36.5 inches and make another mark, repeat on the other side.

  • Attach the last two braces with the marks you made on the inside of the frame, in the middle of the brace, using wood glue. On the outside of the frame, put one screw into each mark all the way around. Then, go to each mark and put a screw on both sides of the first screw, about 1 inch apart.

  • Place the plywood bottom on the frame and attach to the braces using about four 1 1/4 inch screws in each brace.

  • Measure 5 1/2 inches from the corner in both directions around the frame to make eight marks. Use the drill to make pilot holes for the lag bolts. Insert a screwdriver into the eye of the lag bolts to tighten. Use the drill to make holes in the ceiling for the lag bolts. Use the screwdriver through the eyes of the bolts to tighten.

  • Attach a quick link to the lag bolts in the ceiling and one on each length of chain. Prop the bed to the desired height with sawhorses, and thread the end of the chain without the quick link through each bolt on a corner. Attach the end of the chain to the quick link. Then attach the link to the other quick link already in the ceiling. Repeat for each corner. Each chain will pass through two lag bolts before attaching to the ceiling to make a triangle at each corner.

Tips & Warnings

  • Variations of this bed can be bolted to the wall on one side and held up with cable or rope on the other.
  • Install the lag bolts into joists in the ceiling, not just into Sheetrock.

Related Searches

References

  • Photo Credit Jupiterimages/Comstock/Getty Images
Promoted By Zergnet

Comments

Resources

You May Also Like

  • How to Make a Hanging Bed

    You've solved the shared sibling bedroom squabbles by assigning the eldest one a private room in the attic but nixed the request...

  • DIY for Porch Swing Squeaks

    Porch swings invite you to linger and savor the gentle swinging motion as you sway in the breeze. Usually made of wood,...

  • DIY Bed Frame

    Bed frames are available at almost every home design shop, but often they are one of the most expensive things you can...

  • How to Use Pulleys to Make a Ceiling Bed

    A ceiling bed is an innovative way to create additional usable space while at the same time accentuating the design elements of...

  • How to Screw an Eye Bolt Into a Ceiling

    Eye bolts are useful for suspending objects from ceilings. The challenge is properly installing the hardware to support the weight of the...

  • DIY Porch Swing

    Imagine lazy afternoons spent swinging on a handmade porch swing. Pass the lemonade, or count the stars while swaying in the breeze....

  • Porch Swing Frame Ideas

    A porch swing frame can be a lovely and portable way to add an outdoor focal point and a place of quiet...

  • Hanging Bed Canopy Ideas

    You can make canopies to hang behind your headboard or flow gracefully over your bed. Use cornice boards or shelves with drapery...

Related Searches

Check It Out

22 DIY Ways to Update Your Home on a Small Budget

M
Is DIY in your DNA? Become part of our maker community.
Submit Your Work!