How to Electroplate at Home

Save money by electroplating your items at home.
••• Jupiterimages/Photos.com/Getty Images

Electroplating is a huge business considering the number of industries that electroplate their products. Chrome plating is perhaps the most widely known type of plating, but the process produces hazardous waste products. Electroplating is applicable to many metals such as gold, silver, platinum and zinc. Regardless of the type of electroplating, you need to dispose of your waste products properly. The electroplating process requires a battery, a conducting solution that contains ions of the metal you want to plate and something to plate. Zinc plating is one of the easiest types of plating to perform. Follow the example of electroplating a penny with zinc described below.

    Put on the latex gloves for protection and to keep you skin oils from coating the penny or zinc.

    Assemble the plating system by arranging a plastic container, a piece of zinc, a penny, two pieces of wire and a 1.5-volt “D” cell battery.

    Fill the plastic container with vinegar to the halfway mark. This will provide enough vinegar to cover the penny when you place it in the container.

    Attach one wire to the piece of zinc using an alligator clip. Then insert the zinc into the container of vinegar with the wire sticking out of the container. Vinegar is a weak acid and dissolves the zinc. This generates zinc ions in the vinegar. For electroplating to occur the plating solution must contain metal ions of the metal you want to plate. Allow the zinc to remain in the vinegar for at least 15 minutes before beginning the electroplating.

    Dissolve five tablespoons of table sugar and 3-1/2 tablespoons of Epsom salts in the container with the vinegar in it. Mix well until the crystals disappear. The Epsom salt makes the solution conductive and the sugar promotes a shiny finish. The sugar is a brightener that inhibits large crystal growth at the cathode during plating and allows even plating over the whole cathode. Use Epsom salt instead of table salt to eliminate the possibility of producing chlorine gas during the plating process.

    Clean the surface of the penny by brushing it with a toothbrush and a small amount of toothpaste. The surface of the penny should appear shiny after this cleaning.

    Dip the penny into the container of vinegar. Use an alligator clip to attach the penny to the wire. The only thing remaining to add is the battery to drive the electroplating process.

    Attach the wire connected to the piece of zinc to the negative post of the “D” cell. Connect the wire holding the penny to the positive post of the “D” cell. The current will begin to flow between the zinc and the penny by the movement of the metal ions and counter ions from the salt. The voltage of the battery is small enough that the plating will occur slowly and more even than with a high voltage battery.

    Allow the plating to continue for approximately 30 minutes to obtain a heavy layer on the penny.

    Disconnect the battery from the penny and piece of zinc. Remove the penny from the alligator clip and rinse in water. Polish the zinc coating using a small amount of toothpaste and a toothbrush.

    Things You'll Need

    • Latex gloves
    • 1-quart plastic container
    • Piece of zinc
    • Penny
    • Two lengths of wire
    • 1.5 volt “D” cell battery
    • Vinegar
    • Alligator clips
    • Sugar
    • Epsom salt
    • Toothbrush
    • Toothpaste

    Tips

    • If you want to plate larger pieces, you should increase the size of the battery.

      Higher voltage will decrease the time required to plate, but if you go too high, the finish will not look as good.

    Warnings

    • Store or dispose of your plating solution properly. The solution contains hazardous materials.

Related Articles

Homemade Edison Cell
What Are Some Possible Materials You Could Use to Make...
Recondition a NiCAD Battery
How Do Batteries Work? Parts, Types & Terminology (w/...
How to Galvanize Metal
How to Electroplate Silver
Bronze Plating Process
Experiments on Cleaning Pennies
What Are Three Important Parts Needed to Make a Battery?
How to Make a Battery With Coke & Vinegar
Batteries Rely on What to Separate Positive & Negative...
Making Electricity From Salt Water
Parts of a Battery
How to Make a Solar Cell Out of Household Materials
How to Anodize Copper
How to Use Vinegar & Salt to Make a Penny Disappear
Will Batteries Discharge if You Throw Them in a Bag...
What Are the Elements of an Alkaline Battery?
Experiments With Salt and Vinegar
Can Fruits Make Electricity?

Dont Go!

We Have More Great Sciencing Articles!