The Toyota Previa struts consist of several different parts that work together to form the suspension on the front of the vehicle. These parts include the coil springs, spring seats, shock absorber, strut bearing and wheel knuckle. When the strut goes bad, you may notice excessive bouncing,or bottoming out when you are driving the vehicle. When you change the struts on the Previa, you should consider changing the coil springs as well since everything will be taken apart.
Things You'll Need
- Automobile jack
- Jack stand
- Wheel chocks
- Lug wrench
- Socket set
- Wrench set
- Spring compressor
- Wire ties
Place a set of wheel chocks behind the rear wheels of the Previa. Lift the front of the automobile on the side that you are starting with. Place a jack stand under the Previa and raise it to the frame of the vehicle. Remove the wheel using the lug wrench to loosen the lug nuts.
Remove the brake caliper by loosening the retaining pins with a socket and ratchet. Secure the caliper out of the way using a wire tie. Do not allow it to hang by the hose. Remove the brake rotor from the wheel. Disconnect the ABS sensor from the strut if the Previa has anti-lock brakes.
Remove the nut securing the brake hose bracket to the strut with a wrench. Disconnect the stabilizer bar link using a wrench. Loosen the two lower bolts on the strut assembly with a socket and ratchet but do not remove them. Remove the cotter pin from the tie-rod end using the pliers.
Remove the castellated nut with a wrench. Separate the tie-rod end from the wheel knuckle. Remove the top three bolts from the strut using a socket and ratchet. Access the bolts from inside the engine compartment on the wheel well. Remove the bottom bolts and take the strut from under the Previa.
Place the spring compressor on the coil spring and tighten it enough that the pressure is taken off the spring seats. Remove the center nut from the strut shaft using a wrench. Remove the coil spring cap, coil spring and spring seats from the strut. Put the coil spring on the new strut along with the spring seats and cap.
Install the center nut and tighten it with a wrench. Place the strut on the Previa and loosely install the two bottom bolts. Connect the top three bolts and tighten them with a socket and ratchet. Tighten the bottom bolts with a socket and ratchet. Connect the tie rod to the wheel knuckle. Install the castellated nut and tighten it with a socket and ratchet.
Insert a new cotter pin in the tie-rod end and spread it open with the pliers. Connect the stabilizing bar link. Tighten the bolt with a wrench. Connect the brake hose bracket to the strut and tighten the nut with a wrench. Connect the ABS sensor if the Previa has antilock brakes.
Put the brake rotor on the wheel assembly. Cut the wire tie securing the caliper using the pliers. Place the caliper in the mounting cradle and tighten the locking pins with a socket and ratchet. Install the wheel on the Previa. Tighten the lug nuts with a lug wrench. Remove the jack stand from under the Previa. Lower the vehicle to the ground.
Tips & Warnings
- Wear a pair of safety goggles to prevent eye injury.
- Do not attempt this procedure without the spring compressor or it will be impossible to reassemble the strut.
How to Replace a Tie Rod End in a Toyota Tundra
The tie rod ends connect the tie rod to the steering knuckle and keep the tires aligned on your Toyota Tundra. If...
How to Change Front Brake Pads
Replacing your front brake pads is a relatively simple procedure, and it's necessary that it be done from time-to-time. As brake pads...
How to Change Toyota Struts
When struts wear out, choppy wear on the tires that leave little uneven flat spots on the tread appear. The front or...
How to Replace the Struts on a Solara
The struts on your Toyota Solara are responsible for the suspension on your vehicle and operate in the same way that shock...
How to Change the Oil in a Toyota Previa
Changing the oil of a Toyota Previa is a challenging, but not impossible task. Because the oil tank is located on the...