A combination of metal and flexible rubber brake lines carry brake fluid from the master cylinder to each each wheel cylinder or caliper. Sometimes the lines travel through a proportioning block where the line pressure becomes equalized, then travels to the brake cylinders or calipers. Brake lines suffer impact breakage and corrosion over time and need to be replaced. Some occasions call for replacing just a section of brake line rather than the entire length. Joining two brake lines together with a new spliced section can be accomplished with a few specialty tools and some basic steps.
Things You'll Need
- Floor jack
- Jack stands
- Drain pan/s
- Tape measure
- Pipe cutter
- Wire brush
- Fuel line wrenches
- End wrenches
- Flare line tool kit
Set the shift selector in park or neutral, depending on your transmission type. Set the emergency brake firmly. Use a floor jack to raise the vehicle high enough to place two jack stands under the rear frame. Raise the front of the vehicle and place two jack stands under the front frame. Place a drain pan (or two) under the damaged section of brake line, where you intend to cut it. Unclasp the brake line from its plastic hangers, allowing enough line to drop a foot or more.
Place a pipe cutter around one section of the brake line and turn the knob clockwise. Rotate the cutter in a circle while you turn the cutter knob. Rotate the cutter enough to cut the line. Do the same on the other end of the line. Measure the damaged section of line with a tape measure and and subtract 1/2-inch, for your replacement line length. Use a wire brush to clean the ends of the cut lines on the vehicle.
Sand the ends of the vehicle brake lines to a slight bevel with sandpaper. Curl the sandpaper to fit inside the brake line opening and sand any burs away. Do both lines. Push two male brake line fittings over each of the vehicle's brake lines with the threads pointing outward.
Place one vehicle brake line inside a flare tool block, setting the end of the line 1/4-inch out past the line socket. Tighten the tool block clamps by hand. Refer to the flare tool instructions for the proper flare angle and diameter for your brake line.
Place the flare tool hook clamps around the block and align the conical flare shaft inside the brake line. Twist the T-handle on the flare tool until the flare shaft compresses the end of the line into a mushroom shape. Remove the flare tool and repeat the same process on the other brake line.
Use a pipe cutter to cut your new brake line to your previous measurement, which was 1/4-inch shorter than the old brake line segment. Sand the inside and outside of the brake line end, removing any burs or plastic brake film. Slip two female connectors on each end of the new brake line, with the threads pointing outward. Set one end of the brake line inside the flare tool block, exposing 1/4-inch of line. Tighten the tool block clamps by hand.
Place the flare tool around the block, clamping the ends with the two hooks. Turn the flare tool shaft T-handle until the end of the brake line compresses into a mushroom flare. Repeat the same procedure on the other end of the brake line. Take the new brake line section underneath the vehicle.
Screw one male fitting from the vehicle line into one female fitting on the new line, by hand. Do the other side the same. If you need to, pull the vehicle brake line backward or forward to connect the threads -- they will slide in the hanger fittings. Tighten each fitting by using two opposing fuel line wrenches. Hold the female fitting still with a wrench while you tighten the male fitting clockwise. Tighten both fittings until firmly snug. Snap the brake line back up into the plastic hanger guides.
Tips & Warnings
- You will need to refill the master cylinder with the lost brake fluid and bleed the lines after the splicing procedure. Have an assistant pump up your brake pedal and hold it while you open a bleeder valve with a fuel line wrench to allow the escape of air. Shut the valve and have the assistant pump up the pedal and hold it again. Loosen the valve until a steady stream of brake fluid escapes, then shut the valve. Bleed all the wheel cylinders and calipers this way. Replace the brake fluid in the master cylinder.
- Photo Credit brake image by Jan Will from Fotolia.com
How to Install a Brake Line Lock
A brake line lock is a front brake valve that will close to brake line when initiated by the driver. The system...
How to Undo a Steel Line to Brake Hose Connection
How to remove a car's retaining clip and steel hose. Learn how to remove and replace worn brake hoses in this free...
Cutting Front-to-Rear Brake Lines
How to cut front-to-rear brake lines. Learn how to replace a truck's steel brake lines, brake line removal, and custom brake lines...
Tools for Replacing Steel Brake Lines
What tools do I need to replace steel brake lines? Learn how to replace a truck's steel brake lines, brake line removal,...
How to Install Compression Fittings on Steel Brake Lines
Steel brake lines are designed to withstand far greater pressure levels than normal rubber brake lines. When you jam on the brakes...
How to Clean Brake Lines
A brake fluid flush can make your vehicle safer to operate. Dirty brake lines can cause damage and contamination of other parts...
How to Connect the Leader to Braid Fishing Line
In order to attach a leader to braided fishing line for drop shooting, it's important to pay attention to the diameter of...
How to Cut Metal Pipes
Cutting metal pipes is a necessity when needing an appropriate custom fit for your application. There are different methods and ways of...
Replacing Front Brake Hoses: Open Brake Lines
Comments. Video Transcript. Okay, in this segment we're going to cover removing the brake hose. And we're also going to cover installing...
How to Repair a Fuel Line in a Car
Fuel lines develop leaks when part of the line rubs against anything metal under the vehicle. Typically the frame rail is responsible...