The most stable and long-lasting base for a shed is a concrete pad. The pad should be of the same dimensions or slightly larger than the shed to provide a proper anchor for it. Once built, the shed will be a permanent structure, so take your time with the planning phase of the project to ensure that the shed is placed in the best spot relative to your needs.
Things You'll Need
- Marking paint
- 2-inch by 6-inch boards
- Wood stakes
- 3-inch nails
- Landscape fabric
- Crushed gravel
- Push broom
Building the Form
If the shed is quite small, place the assembled shed on the ground in the desired location. Mark the perimeter of the shed with marking paint, spraying the paint approximately 2 to 3 inches from the base of the shed. Remove the shed from the location. If the shed will be built later, mark the dimensions on the ground, being sure that the corners are perfectly square. If you need the visual guidance, make another set of marks 2 to 3 inches out from the first set.
Dig out the area within the marked perimeter to a depth of 6 inches. Compact the ground with a hand tamper, which is a long pole with a flat base and two handles on the side, or a mechanical tamper, which is available for rent from most hardware stores.
Spread landscape fabric along the base of the hole, overlapping seams by 3 to 4 inches.
Lay 2-inch by 6-inch boards on edge around the perimeter of the hole to build the basic form. At corners, drive 3-inch nails through an exterior edge into the ends of the adjacent board. Drive nails at an angle through the narrow edge of one board into another board butted up against it to create a side that is more than one board long.
Measure the inside perimeter of the wood form. The measurement should equal or be larger than the exterior perimeter of the shed. Adjust the form as needed to obtain the proper dimensions.
Drive wood stakes with a mallet along the exterior edge of the forms, spaced every 2 to 3 feet. Place a wood stake along each seam or joint between wood beams. The top of each stake must sit flush with or below the top of the wood form.
Place a level on the top of the wood form to gauge side-to-side and front-to-back level. Raise and lower the form inside the hole until the proper level is obtained. Anchor the position of the form by hammering nails through the stakes into the form.
Laying the Pad
Pour a 1-inch-thick layer of crushed gravel over the base of the hole. Compact the gravel with a tamper and check the depth. The depth of the hole should be 5 inches below the top of the wood form. Add and remove gravel as needed to obtain a uniform depth.
Mix concrete and pour it into the hole until the form is half full. Lay out lengths of rebar in a grid pattern across the top of the concrete. Space the rebar every 18 to 24 inches in both directions, creating squares.
Finish filling the form with concrete. Tap the edges of the form with the rubber mallet while pouring the concrete to help remove air pockets.
Drag a spare board across the top of the form to remove excess material and to leave a level surface. Move a float in wide arcs across the surface to smooth the concrete.
Smooth the surface with a trowel once the surface water has evaporated and the concrete takes on a dull, grey appearance. Drag a push broom over the surface to create small grooves for a skid-resistant surface. Allow the concrete to cure before placing or building a shed on it.
Tips & Warnings
- Cover the concrete pad with plastic for seven days to optimize the curing process. The plastic is not required but will assist in keeping the concrete moist while the chemical reaction solidifies the material. Do not wet the surface of the concrete while it is curing. Excess moisture will prolong the process. Allow the concrete to cure and remain stable for two to three weeks before applying any type of sealant or paint.
- Photo Credit Jupiterimages/Photos.com/Getty Images
How to Make a Concrete Base for a Shed
There are sheds that you can build on your own from scratch, and there are sheds that you can buy which you...
How to Lay Pavers on a Concrete Base
Laying pavers on a concrete base is a challenging yet potentially rewarding project. Using an existing concrete base helps ensure a solid,...
Alternative to a Concrete Shed Floor
When you're building a shed, concrete is usually the most typical choice for flooring material. Since concrete is used to form the...
Wood Floors Vs. Concrete for a Shed
When choosing a floor for your shed, first consider your budget to decide what to set aside for the construction costs for...
How Long Should a Concrete Foundation Cure Before Erecting the Building?
How Long Should a Concrete Foundation Cure Before Erecting the Building?. Concrete should be allowed to cure from anywhere between three and...
Typical Thickness of a Concrete Slab for a Shed
A concrete slab makes a good foundation for a storage shed. Concrete is durable. It eliminates the need to build a separate...
How to Lay Slabs for a Shed Base
Many homeowners require storage for tools, bicycles and other equipment, and in doing so they will often purchase a shed to be...
How to Level the Ground for a Rubbermaid Roughneck Storage Shed
The Rubbermaid Roughneck line of storage sheds are a high-density plastic shed. The shed installs much like a big puzzle. The key...
How to Build a Wooden Shed Floor For Storage
The foundation of a wooden shed floor is set upon concrete supports. The joists and side board assembly are mounted upon the...