Quest fittings are plastic compression fittings that will work on copper, polybutylene, PEX and other plastic tubing. They are sized by the inner diameter of the tubing onto which they will be installed. Quest fittings find their widest use in a trailer's plumbing and climate control devices. Whether you need a fitting for a coded-by-color application or one that has a gauge on one end and a needle valve on the other, Quest can oblige your need. Correctly installing these fittings onto whatever material your tubing or hose is made of is the key to a good, tight connection.
Things You'll Need
- Eye protection
- Cordless drill and bit
- Utility knife
- Adjustable wrench
- Teflon tape
Turn off the water to the faucet and fittings you are installing. Use a center punch to make a slight indentation into the line. Drill a pilot hole in the indentation very carefully, using the drill and 1/8-inch bit.
Refer to the diagrams that came with the faucet to mount the chassis punch onto the line. Gradually tighten the nut to create the hole. File the edges free of any burrs created by making the hole.
Take the hardware off the threaded nipple, leaving the chrome base plates and rubber washers on the assembly. Insert the threaded pipe through the sink mounting hole and set the faucet in its permanent position on the sink. From under the sink, slip the spacer, flat washer and hex nut onto the threaded pipe, in that order. Tighten them by hand for now.
Check the permanent positioning of the faucet, and use a wrench to further tighten the assembly you just tightened by hand. You may have to hold the faucet with one hand and tighten with the other when you start to get resistance.
Select a convenient, reachable location on the vertical water line to mount the saddle valve. Hold the back plate against the tube. Place the saddle valve against the tubing directly opposite the back plate. Tighten the screw to secure the valve and back plate in place on the tube. Continue to tighten gradually, without collapsing the tube, until the hole is made.
Slip the nut and sleeve of the Quest fitting onto the tubing. Push the insert into the tubing. Mount the tubing with its insert and sleeve into the valve body. Screw on the compression nut onto the valve body and tighten securely. Turn the tapping valve handle to the right or clockwise until it is completely seated and the piercing needle is fully extended.
Tips & Warnings
- Follow plumbing standards and codes for installing the faucet assembly and Quest fittings.
- To prevent damaging the piercing needle of the saddle valve, do not allow the point to go beyond the rubber gasket.
- Photo Credit gel tubing macro image by laurent dambies from Fotolia.com plumber, plumbing image by Greg Pickens from Fotolia.com old worked off adjustable wrench 4 image by Kostyantyn Ivanyshen from Fotolia.com bricolage.. image by Claudio Calcagno from Fotolia.com
How to Fix Defective Polybutylene Pipes
Polybutylene pipes were the goof of the 1980s and 1990s. These pipes were installed as plumbing in homes and buildings. They were...
How to Install Brass Compression Fittings
A brass compression fitting is an economical and effective tool that can be used to install anything from valves to couplings. It...
How to Install Pex Fittings
PEX fittings are mechanical fittings that do not require heat or glue to install. Types of PEX fittings are: old expansion with...
How to Make a Silencer for a Crosman Quest
A gun suppressor, commonly known as a silencer, muffles the sound that a weapon makes when it is fired. You can make...
How to Install Poly Pipe Fittings
Polyethylene is a material used to create flexible irrigation tubing. The poly tubing is very malleable and can be fitted with sprinklers...
How to Repair a Quest Water Pipe
Quest (polybutylene) water pipes are made of plastic resin and were commonly used in water supply lines in homes from 1978 to...