How to Make Jewelry Out of Watch Parts

Save

The lifetime of watches aren't eternal. Eventually, a watch isn't able to bounce back and simply stops ticking for good. What now, throw it away? No, if you are a creative jewelry maker, you see an opportunity to make "steampunk" jewelry with parts the watch will give up when taken apart. Steampunk is a science fiction and Victorian-era hybrid, and though intimidating, it is easier than anyone would think to put together a jewelry piece made of watch parts. Making a pendant from an old watch would be a good way to venture out and try this art.

Things You'll Need

  • 4-mm. open jump rings, silvertone or goldtone
  • Flat-nose pliers
  • 4-mm. cable chain, 18 inches, silvertone or goldtone to match the watch parts
  • Toggle clasp
  • Bail, double end leaf in silvertone or goldtone
  • Watch drive from a large watch
  • Paper mixing pad
  • Toothpick
  • Round-nose pliers
  • Swarovski crystal flat-back crystal beads
  • Antiqued or patina charms
  • Open a jump ring with the flat-nose pliers.

  • Slide the opened jump ring through one end of the cable chain, and slide the open part of the toggle clasp onto the jump ring.

  • Pinch the jump ring closed with the flat-nose pliers.

  • Bend the double leaf bail in the middle, causing it to close. Do this by holding the stem between the two leaves with the round-nose pliers and bending the leaves toward each other with your fingers.

  • Rough up the edges of the watch drive on both sides, but only where they will be covered by the bail, then roughen the inside of both of the leaves on the bail. This helps the glue to hold longer.

  • Dispense equal amounts of epoxy and accelerant onto the paper mixing pad and mix thoroughly with the toothpick.

  • Load the mixed epoxy inside the inside of the leaves of the bail. Place the bail over the spot you filed on the watch drive, front and back, and use the flat-nose pliers to hold the bail tight and closed until the epoxy is set. Allow it to dry completely.

  • Dispense equal amounts of epoxy and accelerant. Mix with a toothpick.

  • Lay the watch drive down on the work area and using the epoxy, glue the Swarovski crystal flatback to the center of the watch drive, along with any antiqued charms that fit the theme of the necklace. With a Victorian theme, charms such as gloves, Victorian hats, doves and bows work well. Allow the epoxy to completely set.

  • Slide the newly made watch part pendant onto the chain.

  • Open a jump ring with the pliers and slide it through the second end of the chain. Slide the T part of the toggle clasp onto the jump ring. Close the jump ring with the pliers, connect the toggle clasp and the necklace is ready to wear.

References

  • Photo Credit golden watch image by Yulaki Khvenchuk from Fotolia.com
Promoted By Zergnet

Comments

Resources

You May Also Like

  • Necklaces Made With Old Watches

    Necklaces Made With Old Watches. Old watches, particularly antique pocket ... delicate and complicated workings that make attractive jewelry features. Modern watches...

  • How to Make Jewelry Watch Bands

    How to Make Jewelry Watch Bands. Part of the series: How to Make Jewelry. Learn how to make jewelry watch bands in...

  • How to Find Gears for Steampunk Jewelry

    Old brass goggles or early round lens googles for men and jewelry made with clock parts and gears ... These are sometimes...

  • How to Paint Jewelry and Watches

    Since costume jewelry is not made of the same high-quality materials used to make fine jewelry, it is less resistant to wear......

  • How to Recycle Old Watches

    Whether you are looking for some extra cash or you just want to clear out your old jewelry box, there are many......

  • Soldering Silver for Making Jewelry: Part 1

    Part of the series: How to Make Beautiful Jewelry. Learn how to solder the silver when making your own ... life to...

  • What Is Steampunk Jewelry?

    How to Make Jewelry Out of Watch Parts. The lifetime of watches aren't eternal. Eventually, a watch isn't able to bounce back...

  • Jewelry Making Hardware

    Part of the series: How to Make Jewelry. Learn about hardware for making your ... How to Make Jewelry Watch Bands ......

  • Jewelry casting: part 3

    Watch the third step in casting jewelry from molten silver.

  • What Is Steampunk Art?

    Modern robots featuring old-fashioned watch parts, high-tech laptops outfitted with crude wooden and brass casings, and a baby chick mounted to appear...

  • How to Make Cord Jewelry Necklaces

    How to Make Cord Jewelry Necklaces. Part of the series: How to Make Jewelry. ... How to Make Jewelry Watch Bands

Related Searches

Read Article

These Felt Baby Slippers Are Sew Cute: A Free Tutorial

M
Is DIY in your DNA? Become part of our maker community.
Submit Your Work!