DIY Window Security Without Using Bars


Protecting a window from an outside intruder doesn't force you to place bars over the glass, ruining the decor as well as announcing to a possible intruder that you have something worth protecting. There are a number of ways to go about adding security to the window; the procedures require items available at a hardware store and security supply center. A few common supplies and tools from around the house are needed as well.

Things You'll Need

  • Glass cleaning spray
  • Soft cloth
  • Window film
  • Car window squeegee
  • Window sensor plate
  • Window sensor receiver plate
  • Wireless transmitter
  • Wood screws
  • Phillips screwdriver
  • Batteries
  • Wireless control panel
  • Wireless security system
  • Portable drill
  • 1/2-inch drill bit
  • Medium-grit sandpaper
  • Paper towel
  • Window lock
  • Apply security film on the inside of the window to prevent the window from being smashed in. Clean the side of the window that is inside the house by first spraying it with glass cleaning spray. Wipe the window dry with a soft cloth. Place the window film that has been cut to the same dimensions as that of the window at a hardware store on the floor. Remove the paper backing from the window film. Hold the window film with the sticky side facing away from you. Place the top edge of the window film against the top edge of the window, lining up the left and right sides. Press down on the window film as you run it down the length of the window. Squeegee any air bubbles by pressing the edge of a car window squeegee against the top edge of the film and running it down the length of the window.

  • A wireless window sensor will not betray its presence while sending a signal to trigger an alarm if the window is disturbed. First open the window and screw a sensor plate to the bottom of the window with wood screws using a Phillips screwdriver. Close the window almost all the way. Slide the sensor receiver plate onto the window sill so that it lines up with the sensor plate. Raise the window and screw the sensor receiver plate onto the window sill with wood screws using the Phillips screwdriver. Open the compartment lid on the back of the wireless transmitter that is connected to the sensor receiver plate. Insert batteries into the battery compartment and close the lid. Place the wireless transmitter on the wall beneath the window sill. Screw the transmitter to the wall with wood screws using the Phillips screwdriver. Press the "Sync" button on the wireless transmitter and on the wireless control panel for the wireless security system to sync the two.

  • A window security lock will keep the window closed when you want it to be so, yet let you release the lock to open the window at will. Drill a hole partly into the bottom edge of the window on the inside of the home with a portable drill. Smooth the inside edges with medium-grit sandpaper. Wipe the dust and other contaminants from the window sill with a water-moistened paper towel. Place the window lock on the window sill so the locking bar faces the hole. Screw the window lock to the window sill with wood screws using the Phillips screwdriver. Rotate the knurled knob on the top of the window lock clockwise to extend the locking bar into the hole in the window.

Related Searches


Promoted By Zergnet



You May Also Like

  • How to Install Security Bars On Your Windows

    Since they are often out of a neighbor's view or hidden by bushes or shrubs, basement windows make an easy point of...

  • How to Paint Wrought Iron Window Grates

    Do you need an updated look for your Wrought Iron Window Grates? Try these tips.

  • Types of Security Bars for Windows

    Window security bars stop intruders from breaking into homes and businesses. The bars deter thieves visually. Any dwelling with window bars will...

  • DIY Burglar Bars

    Burglar bars protect your home from intruders who would try to enter through the windows. Typically, burglar bars are made of iron...

  • DIY Home Bar Dimensions

    If you're constructing a home bar, the dimensions for height, depth and width are important considerations for optimum functionality. A bar is...

Related Searches

Check It Out

22 DIY Ways to Update Your Home on a Small Budget

Is DIY in your DNA? Become part of our maker community.
Submit Your Work!